362 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.358

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 358 0362 ENG Lab2u

Endmill Series SOLID CARBIDE Endmills GSX Series Solid Carbide Endmills 358 GSX End Mill-INCH 3D Sharp Edge Item Stock Flutes Length Diam. (inch) Dc Diam (mm) Dc Shank Diam. (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX204S-3D O 2 3D 0.0625 1.588 0 .1250 0 .1875 0.2269 1.500 - GSX206S-3D O 2 3D 0.0938 2 .381 0 .1250 0 .2813 0.3206 1.500 - GSX208S-3D O 2 3D 0 .1250 3.175 0 .1250 0.3750 - 2.000 - GSX210S-3D O 2 3D 0 .1563 3. 969 0 .1875 0.4688 0.5278 2.000 - GSX212S-3D O 2 3D 0 .1875 4 .763 0 .1875 0.5625 - 2.000 - GSX214S-3D O 2 3D 0 2188 5.558 0.2500 0.6564 0.735 2.000 - GSX216S-3D O 2 3D 0.2500 6 .350 0.2500 0.7500 - 2.000 - GSX218S-3D O 2 3D 0 2813 7 .145 0 3125 0.8439 0.923 3 .000 - GSX220S-3D O 2 3D 0 3125 7 .938 0 3125 0.9375 - 3 .000 - GSX224S-3D O 2 3D 0.3750 9 .525 0.3750 1.1250 - 3 .500 - GSX228S-3D O 2 3D 0.4375 11.113 0.4375 1.3125 - 3 .500 - GSX232S-3D O 2 3D 0.5000 12 .700 0.5000 1.5000 - 3 .500 - GSX236S-3D O 2 3D 0.5625 14 .288 0.5625 1.6875 - 4.500 - GSX240S-3D O 2 3D 0.6250 15.875 0.6250 1.8750 - 4.500 - GSX244S-3D O 2 3D 0.6875 17 .463 0.6875 2.0625 - 4.500 - GSX248S-3D O 2 3D 0.7500 19 .050 0.7500 2.2500 - 5 .000 - GSX256S-3D O 2 3D 0.8750 22.225 0.8750 2.6250 - 5 .000 - GSX264S-3D O 2 3D 1.0000 25.400 1.0000 3.0000 - 5 .500 - Endmill Identification (GSX MILL Series Only) GSX 2 04 S - 3D Series Code 2 of Flutes Diameter in 64ths 4 5 Cutting Cutting Edge Edge Length S Sharp Edge C Gash Land Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rare cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available O - Items Available 1st Quarter 2015 Recommended Cutting Conditions I Side Milling 3 (4/64 = 0.0625") Work Material Carbon Steel Alloy Steel Tempered Steel, Hardened Steel Cond SS SC (150 to 250HB) FC SCM (25 to 35HRC) NAK, HPM (35 to 45HRC) (45 to 55HRC) SUS304, SUS316 Titanium Alloy Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 18,500 9.84 18,500 9.84 18,500 9.84 17,000 5 .91 11,500 3.94 8,000 2 .56 9,400 2 .56 8,000 1.77 0 .078 9,400 9.84 9,400 9.84 9,400 9.84 8,500 7.87 6,700 5.12 4,000 2 .56 4,600 3 .54 4,000 2 .36 0 .156 4,500 13 .78 4,500 13 .78 4,500 13 .78 4,300 9.84 3,500 8 .27 2,000 4.33 2,300 4.33 2,000 2 .76 0 .236 3,100 15 .75 3,100 15 .75 3,100 15 .75 2,800 11.81 2,400 8 .66 1,300 4.72 1,500 4.72 1,300 3 .54 0 .315 2,300 14 .96 2,300 14 .96 2,300 14 .96 2,100 11.81 1,800 8 .66 950 4.72 1,100 4.72 900 3 .54 0 .393 1,800 13 .78 1,800 13 .78 1,800 13 .78 1,700 11.81 1,400 8 .66 700 4.72 900 4.72 800 3 .54 0 .472 1,500 13 .78 1,500 13 .78 1,500 13 .78 1,400 11.81 1,200 8 .66 650 4.33 750 4.72 650 3 .54 0 .630 1,100 11.81 1,100 11.81 1,100 11.81 1,000 9.45 900 7 .48 480 3 .54 550 3 .94 490 2 .76 0 .787 900 11.02 900 11.02 900 11.02 850 8.27 700 6 .69 400 3 .15 440 3 .54 400 2 .36 Standard ap 2 .5Dc 2 .0Dc Depth-of-cut ae Below 03 0.02Dc From 03 to below 08 0 .05Dc 08 and above 0 .07Dc 0 01 Dc groove Milling Work Material Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond. Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 18,500 9.84 18,500 9.84 18,500 9.84 17,000 5 .91 11,500 3.94 8,000 2 .56 9,400 2 .56 8,000 1.77 0 .078 0 .156 9,400 4,500 9.84 13 .78 9,400 4,500 9.84 13 .78 9,400 4,500 9.84 13 .78 8,500 4,300 7.87 9.84 6,700 3,500 5.12 8 .27 4.000 2.000 2 .56 4.33 4,600 2,300 3 .54 4.33 4.000 2.000 2 .36 2 .76 0 .236 0 .315 3,100 2,300 15 .75 14 .96 3,100 2,300 15 .75 14 .96 3,100 2,300 15 .75 14 .96 2,800 2,100 11.81 11.81 2,400 1,800 8 .66 8 .66 1,300 950 4.72 4.72 1,500 1,100 4.72 4.72 1,300 900 3 .54 3 .54 0 .393 0 .472 1,800 1,500 13 .78 13 .78 1,800 1,500 13 .78 13 .78 1,800 1,500 13 .78 13 .78 1,700 1,400 11.81 11.81 1,400 1,200 8 .66 8 .66 700 650 4.72 4.33 900 750 4.72 4.72 800 650 3 .54 3 .54 0 .630 0 .787 1,100 900 11.81 11.02 1,100 900 11.81 11.02 1,100 900 11.81 11.02 1,000 850 9.45 8.27 900 700 7 .48 6 .69 480 400 3 .54 3 .15 550 440 3 .94 3 .54 490 400 2 .76 2 .36 Standard Dapth-okij ap 0.02Dc Max.