365 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.361

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 361 0365 ENG Lab2u

SOLID CARBIDE GSX Series Solid Carbide Endmills Endmills GSX End Mill-INCH 3DGash Land Item Stock Flutes Length Diam (inch) Dc Diam (mm) Dc Shank Diam (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX404C-3D O 4 3D 0.0625 1.588 0 .1250 0 .1875 0.2269 1. 500 - GSX406C-3D O 4 3D 0.0938 2.381 0 .1250 0 .2813 0.3206 1. 500 - GSX408C-3D O 4 3D 0 .1250 3 .175 0 .1250 0.3750 - 2.000 - GSX410C-3D O 4 3D 0 .1563 3 .969 0 .1875 0.4688 0.5278 2.000 - GSX412C-3D O 4 3D 0 .1875 4.763 0 .1875 0.5625 - 2.000 - GSX414C-3D O 4 3D 0 .2188 5 .558 0.2500 0.6564 0. 735 2.000 - GSX416C-3D O 4 3D 0.2500 6.350 0.2500 0.7500 - 2.000 - GSX418C-3D O 4 3D 0 .2813 7 .145 0 .3125 0.8439 0.923 3 .000 - GSX420C-3D O 4 3D 0 .3125 7.938 0 .3125 0.9375 - 3 .000 - GSX424C-3D O 4 3D 0.3750 9.525 0.3750 1.1250 - 3 500 - GSX428C-3D O 4 3D 0.4375 11.113 0.4375 1.3125 - 3 500 - GSX432C-3D O 4 3D 0.5000 12 .700 0.5000 1.5000 - 3 500 - GSX436C-3D O 4 3D 0.5625 14 .288 0.5625 1.6875 - 4. 500 - GSX440C-3D O 4 3D 0.6250 15 .875 0.6250 1.8750 - 4. 500 - GSX444C-3D O 4 3D 0.6875 17 .463 0.6875 2.0625 - 4. 500 - GSX448C-3D O 4 3D 0.7500 19 .050 0.7500 2.2500 - 5 .000 - GSX456C-3D O 4 3D 0.8750 22.225 0.8750 2.6250 - 5 .000 - GSX464C-3D O 4 3D 1.0000 25.400 1.0000 3.0000 - 5 500 - Endmill Identification (GSX MILL Series Only) GSX 4 04 C - 3D 1 2 3 4 5 Series of Diameter Cutting Cutting Edge Code Flutes in 64ths Edge Length W64 = O.O625") C Ga Land I Recommended Cutting Conditions I Side Milling A 1 O - Items Available 1st Quarter 2015 Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders. 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rare cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available L Work Material Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 21,000 14.17 21,000 14.17 21,000 14.17 19,000 8.66 13,000 5 .51 9,000 3 .54 10,500 3 .54 9,000 2 .56 0 .078 0 .156 10,500 5,200 14.17 19 .69 10,500 5,200 14.17 19 .69 10,500 5,200 14.17 19 .69 9,600 4,800 11.42 14.57 7,500 4,000 7.09 11.02 4,500 2,250 4.33 5 .91 5,200 2,600 4.72 6.30 4,500 2,250 3 .35 3 .94 0 .236 0 .315 3,500 2,600 22 .05 20.47 3,500 2,600 22 .05 20.47 3,500 2,600 22 .05 20.47 3,200 2,400 15 .75 15 .75 2,700 2,000 11.81 11.81 1,500 1,100 6.30 6.30 1,700 1,300 6.69 6.69 1,500 1,100 4.72 4.72 0 .393 0 .472 2,100 1,750 19 .69 19 .69 2,100 1,750 19 .69 19 .69 2,100 1,750 19 .69 19 .69 1,900 1,600 15 .75 15 .75 1,600 1,350 11.81 11.81 900 750 6.30 5 .91 1,000 850 6.30 6.30 900 750 4.72 4.72 0 .630 0 .787 1,300 1,050 16 .54 14 .96 1,300 1,050 16 .54 14 .96 1,300 1,050 16 .54 14 .96 1,200 950 12 .99 11.42 1,000 800 10 .24 9.06 550 450 4.72 4.33 650 500 5 .51 4.72 550 450 3 .94 3 .54 Standard Depth-of-cut ap 2.5Dc 2 .0Dc ae Below 03 0.05Dc From 03 to below 08 0.1Dc 08 and above 0.15Dc 0.02Dc groove Milling Work Material Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond. Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 16,600 5 .51 16,600 5 .51 16,600 5 .51 15,500 3 .94 10,500 3 .94 7,500 2 .76 9,400 2 .36 3,750 0.79 0 .078 0 .156 9,500 5,200 6.30 6.30 9,500 5,200 6.30 7.09 9,500 5,200 6.30 7.09 9,000 4,800 7.09 6.30 6,200 3,400 4.72 4.33 4,500 2,200 3 .54 2 .56 5,200 2,600 3 .15 2 .76 2.250 1.250 1.18 0.98 0 .236 0 .315 3,500 2,600 6.30 6.30 3,500 2,600 7.87 7.87 3,500 2,600 7.87 7.87 3,200 2,400 6.30 6.30 2,550 1,900 4.72 4.72 1,500 1,100 2 .56 2 .56 1,700 1,300 2 .76 2 .76 950 700 0 .98 0 .98 0 .393 0 .472 2,100 1,750 6.30 6.30 2,100 1,750 7.87 7.87 2,100 1,750 7.87 7.87 1,900 1,600 6.30 6.30 1,500 1,250 4.72 4.72 900 750 66 LO Ln CN CN 1,000 850 2 .76 2 .76 550 450 0 .98 0.98 0 .630 0 .787 1,300 1,050 6.30 6.30 1,300 1,050 7.87 7.87 1,300 1,050 7.87 7.87 1,200 950 6.30 6.30 950 750 4.72 4.72 550 450 66 LO LO CN CN 650 500 2 .76 2 .76 350 280 0.98 0.98 SlinWDeMtfl ap 0 .1 Dc 0.2Dc 0.05Dc 0 .1 Dc 361 Endmill Series