368 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.364

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 364 0368 ENG Lab2u

Endmill Series SOLID CARBIDE Endmills GSX Series Solid Carbide Endmills GSX End Mill-INCH 3D Sharp Edge Item Stock Flutes Length Diam (inch) Dc Diam (mm) Dc Shank Diam. (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX404S-3D O 4 3D 0.0625 1.588 0 .1250 0 .1875 0.2269 1.500 - GSX406S-3D O 4 3D 0.0938 2 .381 0 .1250 0 .2813 0.3206 1.500 - GSX408S-3D O 4 3D 0 .1250 3.175 0 .1250 0.3750 - 2.000 - GSX410S-3D O 4 3D 0 .1563 3. 969 0 .1875 0.4688 0.5278 2.000 - GSX412S-3D O 4 3D 0 .1875 4 .763 0 .1875 0.5625 - 2.000 - GSX414S-3D O 4 3D 0 .2188 5.558 0.2500 0.6564 0.735 2.000 - GSX416S-3D O 4 3D 0.2500 6 .350 0.2500 0.7500 - 2.000 - GSX418S-3D O 4 3D 0 .2813 7 .145 0 3125 0.8439 0.923 3 .000 - GSX420S-3D O 4 3D 0 .3125 7 .938 0 3125 0.9375 - 3 .000 - GSX424S-3D O 4 3D 0.3750 9 .525 0.3750 1.1250 - 3 .500 - GSX428S-3D O 4 3D 0.4375 11.113 0.4375 1.3125 - 3 .500 - GSX432S-3D O 4 3D 0.5000 12 .700 0.5000 1.5000 - 3 .500 - GSX436S-3D O 4 3D 0.5625 14 .288 0.5625 1.6875 - 4.500 - GSX440S-3D O 4 3D 0.6250 15 .875 0.6250 1.8750 - 4.500 - GSX444S-3D O 4 3D 0.6875 17 .463 0.6875 2.0625 - 4.500 - GSX448S-3D O 4 3D 0.7500 19 .050 0.7500 2.2500 - 5 .000 - GSX456S-3D O 4 3D 0.8750 22.225 0.8750 2.6250 - 5 .000 - GSX464S-3D O 4 3D 1.0000 25.400 1.0000 3.0000 - 5 .500 - Endmill Identification (GSX Series Only) GSX 4 04 S - 3D Series Code 2 of Flutes Diameter in 64ths 4 Cutting Edge Cutting Edge Length O - Items Available 1st Quarter 2015 Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders. 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rare cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available Side Milling 3 5 S Sharp Edge C Gash Land (4/64 = 0.0625") Work Material Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 18,500 9.843 18,500 9.843 18,500 9.843 17,000 5 .906 11,500 3 .937 8,000 2 .559 9,400 2 .559 8,000 1.772 0 .078 0 .156 9,400 4,500 9.843 13 .780 9,400 4,500 9.843 13 .780 9,400 4,500 9.843 13 .780 8,500 4,300 7.874 9.843 6,700 3,500 5 .118 8.268 4.000 2.000 2 .559 4.331 4,600 2,300 3 .543 4.331 4.000 2.000 2 .362 2 .756 0 .236 0 .312 3,100 2,300 15 .748 14 .961 3,100 2,300 15 .748 14 .961 3,100 2,300 15 .748 14 .961 2,800 2,100 11.811 11.811 2,400 1,800 8 .661 8 .661 1,300 950 4.724 4.724 1,500 1,100 4.724 4.724 1,300 900 3 .543 3 .543 0 .393 0 .472 1,800 1,500 13 .780 13 .780 1,800 1,500 13 .780 13 .780 1,800 1,500 13 .780 13 .780 1,700 1,400 11.811 11.811 1,400 1,200 8 .661 8 .661 700 650 4.724 4.331 900 750 4.724 4.724 800 650 3 .543 3 .543 0 .630 0 .787 1,100 900 11.811 11.024 1,100 900 11.811 11.024 1,100 900 11.811 11.024 1,000 850 9.449 8.268 900 700 7.480 6.693 480 400 3 .543 3 .150 550 440 3 .937 3 .543 490 400 2 .756 2 .362 Standard Depth-of-cut ap 2 .5Dc 2 .0Dc ae Below 03 0.02Dc From 03 to below 08 0 .05Dc 08 and above 0 .07Dc 0 01 Dc groove Milling Work Material Structural Steel Carbon Steel SC (150 to 250HB) Cast Iron Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel Hardened Steel Stainless Steel Heat Resistive Steel Cond. SS FC (35 to 45HRC) (45 to 55HRC) SUS304, SUS316 Titanium Alloy Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 18,500 9.843 18,500 9.843 18,500 9.843 17,000 5 .906 11,500 3 .937 8,000 2 .559 9,400 2 .559 8,000 1.772 0 .078 9,400 9.843 9,400 9.843 9,400 9.843 8,500 7.874 6,700 5 .118 4,000 2 .559 4,600 3 .543 4,000 2 .362 0 .156 4,500 13 .780 4,500 13 .780 4,500 13 .780 4,300 9.843 3,500 8.268 2,000 4.331 2,300 4.331 2,000 2 .756 0 .236 3,100 15 .748 3,100 15 .748 3,100 15 .748 2,800 11.811 2,400 8 .661 1,300 4.724 1,500 4.724 1,300 3 .543 0 .312 2,300 14 .961 2,300 14 .961 2,300 14 .961 2,100 11.811 1,800 8 .661 950 4.724 1,100 4.724 900 3 .543 0 .393 1,800 13 .780 1,800 13 .780 1,800 13 .780 1,700 11.811 1,400 8 .661 700 4.724 900 4.724 800 3 .543 0 .472 1,500 13 .780 1,500 13 .780 1,500 13 .780 1,400 11.811 1,200 8 .661 650 4.331 750 4.724 650 3 .543 0 .630 1,100 11.811 1,100 11.811 1,100 11.811 1,000 9.449 900 7.480 480 3 .543 550 3 .937 490 2 .756 0 .787 900 11.024 900 11.024 900 11.024 850 8.268 700 6.693 400 3 .150 440 3 .543 400 2 .362 Std M-out ap 0.02Dc Max. 364