366 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.362

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 362 0366 ENG Lab2u

Endmill Series SOLID CARBIDE Endmills GSX Series Solid Carbide Endmills GSX End Mill-INCH 4D Gash Land Item Stock Flutes Length Diam. (inch) Dc Diam (mm) Dc Shank Diam. (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX404C-4D O 4 4D 0.0625 1. 588 0 .1250 0.2500 0.2894 1.500 - GSX406C-4D O 4 4D 0.0938 2. 381 0 .1250 0.3750 0 .4144 1.500 - GSX408C-4D O 4 4D 0 .1250 3 .175 0 .1250 0.5000 - 2.000 - GSX410C-4D O 4 4D 0 .1563 3 .969 0 .1875 0.6250 0.6841 2.000 - GSX412C-4D O 4 4D 0 .1875 4. 763 0 .1875 0.7500 - 2.500 - GSX414C-4D O 4 4D 0 2188 5 558 0.2500 0.8752 0.954 2.500 - GSX416C-4D O 4 4D 0.2500 6. 350 0.2500 1.0000 - 2.500 - GSX418C-4D O 4 4D 0 2813 7 .145 0 3125 1.1252 1.204 3 .000 - GSX420C-4D O 4 4D 0 3125 7.938 0 3125 1.2500 - 3 .000 - GSX424C-4D O 4 4D 0.3750 9. 525 0.3750 1.5000 - 3 .500 - GSX428C-4D O 4 4D 0.4375 11.113 0.4375 1.7500 - 4.000 - GSX432C-4D O 4 4D 0.5000 12 .700 0.5000 2.0000 - 4.000 - GSX436C-4D O 4 4D 0.5625 14 .288 0.5625 2.2500 - 5 .000 - GSX440C-4D O 4 4D 0.6250 15.875 0.6250 2.5000 - 5 .000 - GSX444C-4D O 4 4D 0.6875 17 .463 0.6875 2.7500 - 5 .000 - GSX448C-4D O 4 4D 0.7500 19 .050 0.7500 3.0000 - 5 .500 - GSX456C-4D O 4 4D 0.8750 22.225 0.8750 3.5000 - 5 .500 - GSX464C-4D O 4 4D 1.0000 25.400 1.0000 4.0000 - 6.000 - Endmill Identification (GSX MILL Series Only) GSX 4 04 C - 4D Series Code 2 of Flutes 3 Diameter in 64ths (4/64 = 0.0625") 4 5 Cutting Cutting Edge Edge Length S Sharp Edge C Gash Land I Recommended Cutting Conditions I Side Milling O - Items Available 1st Quarter 2015 Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rare cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 This series is not recommended for grooving 7 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available L Work Material Carbon Steel Alloy Steel Tempered Steel, Hardened Steel Cond. SS SC (150 to 250HB) FC SCM (25 to 35HRC) NAK, HPM (35 to 45HRC) (45 to 55HRC) SUS304, SUS316 Titanium Alloy Dc0mm0 Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 9,000 5 .51 9,000 5 .51 9,000 5 .51 7,000 3 .15 6,500 2 .36 4,500 1.57 5,400 1.57 4,500 1.57 0 .078 4,500 5 .51 4,500 5 .51 4,500 5 .51 3,500 3 .94 3,200 3 .15 2,300 2 .17 2,700 2 .17 2,300 1.57 0 .156 2,250 7.87 2,250 7.87 2,250 7.87 1,750 4.72 1,600 3 .94 1,200 2 .36 1,350 1.97 1,200 1.38 0 .236 1,500 9.84 1,500 9.84 1,500 9.84 1,150 6.30 1,050 5 .51 800 2 .56 900 1.77 800 1.38 0 .315 1,100 8.66 1,100 8.66 1,100 8.66 850 6.30 800 5 .12 600 2 .56 660 1.77 600 1.38 0 .393 900 8.27 900 8.27 900 8.27 700 5 .51 650 4.72 460 2 .56 540 1.77 460 1.38 0 .472 750 7.87 750 7.87 750 7.87 580 5 .51 520 4.33 400 2 .56 450 1.77 400 1.38 0 .630 550 6.69 550 6.69 550 6.69 440 4.72 400 3 .74 300 2 .17 330 1.77 300 1.38 0 .787 450 5 .91 450 5 .91 450 5 .91 350 3 .94 320 3 .15 240 1.97 270 1.77 240 1.38 Standard ap 3 .5Dc 3 .0Dc Depth-of-cut ae Below 03 0.04Dc From 03 to below 08 0 .08Dc 08 and above 0 .1Dc 0.02Dc 362