360 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.356

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 356 0360 ENG Lab2u

Endmill Series SOLID CARBIDE Endmills GSX Series Solid Carbide Endmills GSX End Mill-INCH 4D Gash Land Item Stock Flutes Length Diam. (inch) Dc Diam (mm) Dc Shank Diam. (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX204C-4D O 2 4D 0.0625 1.588 0 .1250 0.2500 0.2894 1.500 - GSX206C-4D O 2 4D 0.0938 2 .381 0 .1250 0.3750 0 .4144 2.000 - GSX208C-4D O 2 4D 0 .1250 3.175 0 .1250 0.5000 - 2.000 - GSX210C-4D O 2 4D 0 .1563 3. 969 0 .1875 0.6250 0.6841 2.000 - GSX212C-4D O 2 4D 0 .1875 4 .763 0 .1875 0.7500 - 2.500 - GSX214C-4D O 2 4D 0 2188 5.558 0.2500 0.8752 0.954 2.500 - GSX216C-4D O 2 4D 0.2500 6 .350 0.2500 1.0000 - 2.500 - GSX218C-4D O 2 4D 0 2813 7 .145 0 3125 1.1252 1.204 3 .000 - GSX220C-4D O 2 4D 0 3125 7 .938 0 3125 1.2500 - 3 .000 - GSX224C-4D O 2 4D 0.3750 9 .525 0.3750 1.5000 - 3 .500 - GSX228C-4D O 2 4D 0.4375 11.113 0.4375 1.7500 - 4.000 - GSX232C-4D O 2 4D 0.5000 12 .700 0.5000 2.0000 - 4.000 - GSX236C-4D O 2 4D 0.5625 14 .288 0.5625 2.2500 - 5 .000 - GSX240C-4D O 2 4D 0.6250 15.875 0.6250 2.5000 - 5 .000 - GSX244C-4D O 2 4D 0.6875 17 .463 0.6875 2.7500 - 5 .000 - GSX248C-4D O 2 4D 0.7500 19 .050 0.7500 3.0000 - 5 .500 - GSX256C-4D O 2 4D 0.8750 22.225 0.8750 3.5000 - 5 .500 - GSX264C-4D O 2 4D 1.0000 25.400 1.0000 4.0000 - 6.000 - O - Items Available 1st Quarter 2015 Endmill Identification (GSX MILL Series Only) GSX 2 04 C - 4D Series Code 2 of Flutes Diameter in 64ths 4 5 Cutting Cutting Edge Edge Length (4/64 = 0.0625") S Sharp Edge C Gash Land Recommended Cutting Conditions I Side Milling Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rear cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 This series is not recommended for grooving 7 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available L 3 Work Material Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond. Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 0 .078 0 .156 9,000 4,500 2,250 5.12 7 .09 9 .45 9,000 4,500 2,250 5.12 7 .09 9.45 9,000 4,500 2,250 5.12 7.09 9.45 7,000 3,500 1,750 3.74 4 .72 6 .30 6,500 3,200 1,600 1.97 2.76 3 .74 4,500 2,300 1,200 1.18 1.57 2 .36 5,400 2,700 1,350 1.57 1.97 2 .56 4,500 2,300 1,200 0.98 1.38 1.57 0 .236 0 .315 1,500 1,100 11.81 10 .24 1,500 1,100 11.81 10 .24 1,500 1,100 11.81 10 .24 1,150 850 6.69 6.69 1,050 800 4.33 4.33 800 600 2 .76 2 .76 900 660 2 .76 2 .76 800 600 1.97 1.97 0 .393 0 .472 0 .630 0 .787 900 750 550 450 9.84 9.45 7.87 7.09 900 750 550 450 9.84 9.45 7.87 7.09 900 750 550 450 9.84 9.45 7.87 7.09 700 580 440 350 6.30 6.30 5 .51 4.72 650 520 400 320 4.33 4.33 3 .74 3 .35 460 400 300 240 2 .76 2 .76 2 .17 1.77 540 450 330 270 2 .76 2 .76 2 .36 1.97 460 400 300 240 1.97 1.97 1.77 1.57 Standard Depth-of-cut ap 3 .5Dc 3 .0Dc ae 0.08Dc I 0.04Dc 356 0Ds h5