359 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.355

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 355 0359 ENG Lab2u

SOLID CARBIDE GSX Series Solid Carbide Endmills Endmills GSX End Mill-INCH 3D Gash Land Item Stock Flutes Length Diam. (inch) Dc Diam (mm) Dc Shank Diam (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX204C-3D O 2 3D 0.0625 1.588 0 .1250 0 .1875 0.2269 1.500 - GSX206C-3D O 2 3D 0.0938 2.381 0 .1250 0 2813 0.3206 1.500 - GSX208C-3D O 2 3D 0 .1250 3.175 0 .1250 0.3750 - 2.000 - GSX210C-3D O 2 3D 0 .1563 3.969 0 .1875 0.4688 0.5278 2.000 - GSX212C-3D O 2 3D 0 .1875 4.763 0 .1875 0.5625 - 2.000 - GSX214C-3D O 2 3D 0 .2188 5.558 0.2500 0.6564 0.735 2.000 - GSX216C-3D O 2 3D 0.2500 6.350 0.2500 0.7500 - 2.000 - GSX218C-3D O 2 3D 0 .2813 7.145 0 .3125 0.8439 0.923 3 .000 - GSX220C-3D O 2 3D 0 .3125 7.938 0 .3125 0.9375 - 3 .000 - GSX224C-3D O 2 3D 0.3750 9.525 0.3750 1.1250 - 3 .500 - GSX228C-3D O 2 3D 0.4375 11.113 0.4375 1. 3125 - 3 .500 - GSX232C-3D O 2 3D 0.5000 12.700 0.5000 1.5000 - 3 .500 - GSX236C-3D O 2 3D 0.5625 14.288 0.5625 1.6875 - 4.500 - GSX240C-3D O 2 3D 0.6250 15.875 0.6250 1.8750 - 4.500 - GSX244C-3D O 2 3D 0.6875 17.463 0.6875 2.0625 - 4.500 - GSX248C-3D O 2 3D 0.7500 19.050 0.7500 2.2500 - 5 .000 - GSX256C-3D O 2 3D 0.8750 22.225 0.8750 2.6250 - 5 .000 - GSX264C-3D O 2 3D 1.0000 25.400 1.0000 3.0000 - 5 .500 - Endmill Identification (GSX MILL Series Only) GSX 2 04 C - 3D Series Code 2 of Flutes 3 Diameter in 64ths (4/64 = 0.0625") 4 Cutting Edge S:Sharp Edge C Gash Land Cutting Edge Length I Recommended Cutting Conditions I Side Milling Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 In rare cases, chattering may occur in early milling stages, dissipating after 2m of cutting 5 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 6 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available rH O - Items Available 1st Quarter 2015 1 0Dc Work Material Cond. Structural Steel SS Carbon Steel SC (150 to 250HB) Cast Iron FC Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel NAK, HPM (35 to 45HRC) Hardened Steel (45 to 55HRC) Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Dc (in) Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) 0 .039 16,600 7.48 16,600 7.48 16,600 7.48 15,500 5 .51 10,500 2 .76 7,500 1.77 9,400 1.97 7,500 1.38 0 .078 9,500 9.84 9,500 9.84 9,500 9.84 9,000 7 .87 6,200 4.72 4,500 2 .36 5,200 2.76 4,500 1.97 0 .156 5,200 12 .99 5,200 12 .99 5,200 12 .99 4,800 7 .87 3,400 5 .91 2,250 2.95 2,600 3.54 2,250 2 .56 0 .236 3,500 14.17 3,500 14.17 3,500 14.17 3,200 9 .84 2,550 6 .69 1,500 3.54 1,700 3.94 1,500 3 .15 0 .315 2,600 12 .60 2,600 12 .60 2,600 12 .60 2,400 9.45 1,900 6 .69 1,100 3.54 1,300 3 .94 1,100 3 .15 0 .393 2,100 11.81 2,100 11.81 2,100 11.81 1,900 9.06 1,500 6 .69 900 3 .54 1,000 3 .94 900 3 .15 0 .472 1,750 11.02 1,750 11.02 1,750 11.02 1,600 9.06 1,250 6.69 750 3 .54 850 3 .94 750 3 .15 0 .630 1,300 9.45 1,300 9.45 1,300 9.45 1,200 7.87 950 5 .91 550 2 .95 650 3 .35 550 2 .56 0 .787 1,050 8.66 1,050 8.66 1,050 8.66 950 7.09 750 5 .51 450 2 .76 500 2 .95 450 2 .36 Standard ap 2 .5Dc 2 .0Dc Depth-of-cut ae Below 03 0 .05Dc 03 and above 0 .1Dc 0.02Dc groove Milling Work Material Structural Steel Carbon Steel SC (150 to 250HB) Cast Iron Alloy Steel SCM (25 to 35HRC) Tempered Steel, Hardened Steel Hardened Steel Stainless Steel Heat Resistive Steel Cond. SS FC (35 to 45HRC) (45 to 55HRC) SUS304, SUS316 Titanium Alloy Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 16,600 2 .76 16,600 3 .15 16,600 3 .15 15,500 1.97 10,500 1.97 7,500 1.38 9,400 1.18 3,750 0.39 0 .078 9,500 3 .15 9,500 3 .94 9,500 3 .94 9,000 3 .54 6,200 2 .36 4,500 1.77 5,200 1.57 2,250 0.59 0 .156 5,200 4.72 5,200 5 .91 5,200 5 .91 4,800 4.72 3,400 3 .15 2,200 1.97 2,600 1.97 1,250 0.79 0 .236 3,500 5 .51 3,500 6.69 3,500 6.69 3,200 5 .12 2,550 3.94 1,500 1.97 1,700 2 .36 950 0.98 0 .315 2,600 5 .51 2,600 6.30 2,600 6.30 2,400 5 .12 1,900 3.94 1,100 1.97 1,300 2 .36 700 0.98 0 .393 2,100 5 .12 2,100 5 .91 2,100 5 .91 1,900 4.72 1,500 3.54 900 1.97 1,000 2 .36 550 0.98 0 .472 1,750 5 .12 1,750 5 .91 1,750 5 .91 1,600 4.72 1,250 3.54 750 1.97 850 2 .36 450 0.98 0 .630 1,300 4.33 1,300 5 .12 1,300 5 .12 1,200 4.33 950 3.15 550 1.77 650 1.97 350 0.79 0 .787 1,050 3 .94 1,050 4.72 1,050 4.72 950 3 .94 750 2.76 450 1.57 500 1.57 280 0.59 Standad feptk>kut ap 0 .1 Dc 0.2Dc 0.05Dc 0 .1 Dc 355 Endmill Series