361 Каталог SUMITOMO 2015 Режущий инструмент и инструментальная оснастка Стр.357

Каталог SUMITOMO 2015 Инструмент и оснастка Стр. 357 0361 ENG Lab2u

SOLID CARBIDE GSX Series Solid Carbide Endmills Endmills GSX End Mill-INCH 2D Sharp Edge Item Stock Flutes Length Diam. (inch) Dc Diam (mm) Dc Shank Diam. (inch) Ds Flute Length (inch) I Neck Length (inch) l2 OAL (inch) L R (inch) GSX204S-2D O 2 2D 0.0625 1.588 0 .1250 0 .1250 0 .1644 1.500 - GSX206S-2D O 2 2D 0.0938 2 .381 0 .1250 0 .1875 0.2269 1.500 - GSX208S-2D O 2 2D 0 .1250 3.175 0 .1250 0.2500 - 2.000 - GSX210S-2D O 2 2D 0 .1563 3. 969 0 .1875 0 .3125 0 .3716 2.000 - GSX212S-2D O 2 2D 0 .1875 4 .763 0 .1875 0.3750 - 2.000 - GSX214S-2D O 2 2D 0 2188 5.558 0.2500 0.4376 0 .516 2.000 - GSX216S-2D O 2 2D 0.2500 6 .350 0.2500 0.5000 - 2.000 - GSX218S-2D O 2 2D 0 2813 7 .145 0 3125 0.5626 0.641 2.500 - GSX220S-2D O 2 2D 0 3125 7 .938 0 3125 0.6250 - 2.500 - GSX224S-2D O 2 2D 0.3750 9 .525 0.3750 0.7500 - 3 .000 - GSX228S-2D O 2 2D 0.4375 11.113 0.4375 0.8750 - 3 .000 - GSX232S-2D O 2 2D 0.5000 12 .700 0.5000 1.0000 - 3 .000 - GSX236S-2D O 2 2D 0.5625 14 .288 0.5625 1.1250 - 3 .500 - GSX240S-2D O 2 2D 0.6250 15.875 0.6250 1.2500 - 3 .500 - GSX244S-2D O 2 2D 0.6875 17 .463 0.6875 1.3750 - 4.000 - GSX248S-2D O 2 2D 0.7500 19 .050 0.7500 1.5000 - 4.000 - GSX256S-2D O 2 2D 0.8750 22.225 0.8750 1.7500 - 4.000 - GSX264S-2D O 2 2D 1.0000 25.400 1.0000 2.0000 - 4.000 - Endmill Identification (GSX MILL Series Only) GSX 2 04 S - 2D Series Code 2 3 of Diameter Flutes in 64ths (4/64 = 0.0625") 4 5 Cutting Cutting Edge Edge Length O - Items Available 1st Quarter 2015 Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders. 2 Use air blow when dry machining 3 Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications 4 If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut 5 This series is not recommended for groove milling 6 If the machine cannot achieve the recommended spindle speed, please use the max spindle speed available S Sharp Edge C Gash Land Recommended Cutting Conditions I Side Milling L Work Material Cond. Structural Steel SS Carbon Steel SC 150 to 250HB Cast Iron FC Alloy Steel SCM 25 to 35HRC Tempered Steel, Hardened Steel NAK, HPM 35 to 45HRC Hardened Steel 45 to 55HRC Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Dc (in) Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) (min-1) (IPM) 0 .039 22,000 14.17 22,000 14.17 22,000 14.17 19,000 8.66 13,000 5 .51 9,500 3 .54 11,300 3 .54 9,500 2 .56 0 .078 11,500 17 .32 11,500 17 .32 11,500 17 .32 11,000 11.42 7,500 7.09 5,400 4.33 6,500 4.72 5,400 3 .35 0 .156 6,000 22 .05 6,000 22 .05 6,000 22 .05 5,800 14.57 4,000 9.06 2,900 5 .91 3,400 6.30 2,900 3 .94 0 .236 4,200 23 .62 4,200 23 .62 4,200 23 .62 4,000 15 .75 2,700 9.45 2,000 6.30 2,400 6.69 2,000 4.72 0 .315 3,000 23 .62 3,000 23 .62 3,000 23 .62 2,800 15 .75 2,000 9.45 1,450 6.30 1,800 6.69 1,450 4.72 0 .393 2,500 23 .62 2,500 23 .62 2,500 23 .62 2,350 15 .75 1,600 9.45 1,200 6.30 1,450 6.69 1,200 4.72 0 .472 2,100 23 .62 2,100 23 .62 2,100 23 .62 2,000 15 .75 1,350 9.45 1,000 6.30 1,200 6.69 1,000 4.72 0 .630 1,500 19 .69 1,500 19 .69 1,500 19 .69 1,450 12 .60 1,000 8.27 750 5 .12 900 5 .51 750 3 .54 0 .787 1,200 18 .11 1,200 18.11 1,200 18.11 1,150 11.42 800 7.87 600 4.33 700 4.72 600 2 .95 Standard ap 2 .0Dc Depth-of-cut ae 0.03Dc 0 01 Dc groove Finishing Work Material Structural Steel SS Carbon Steel SC 150 to250HB Cast Iron FC Alloy Steel SCM 25 to 35HRC Tempered Steel, Hardened Steel NAK, HPM 35 to 45HRC Hardened Steel 45 to 55HRC Stainless Steel SUS304, SUS316 Heat Resistive Steel Titanium Alloy Cond. Dc (in) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) Spindle Speed (min-1) Feed Rate (IPM) 0 .039 22,000 14.17 22,000 14.17 22,000 14.17 19,000 8.66 13,000 5 .51 9,500 3 .54 11,300 3 .54 9,500 2 .56 0 .078 0 .156 11,500 6,000 17 .32 22 .05 11,500 6,000 17 .32 22 .05 11,500 6,000 17 .32 22 .05 11,000 5,800 11.42 14.57 7,500 4,000 7.09 9.06 5,400 2,900 4.33 5 .91 6,500 3,400 4.72 6.30 5,400 2,900 3 .35 3 .94 0 .236 0 .315 4,200 3,000 23 .62 23 .62 4,200 3,000 23 .62 23 .62 4,200 3,000 23 .62 23 .62 4,000 2,800 15 .75 15 .75 2,700 2,000 9.45 9.45 2,000 1,450 6.30 6.30 2,400 1,800 6.69 6.69 2,000 1,450 4.72 4.72 0 .393 0 .472 2,500 2,100 23 .62 23 .62 2,500 2,100 23 .62 23 .62 2,500 2,100 23 .62 23 .62 2,350 2,000 15 .75 15 .75 1,600 1,350 9.45 9.45 1,200 1,000 6.30 6.30 1,450 1,200 6.69 6.69 1,200 1,000 4.72 4.72 0 .630 0 .787 1,500 1,200 19 .69 18.11 1,500 1,200 19 .69 18.11 1,500 1,200 19 .69 18.11 1,450 1,150 12 .60 11.42 1,000 800 8.27 7.87 750 600 5 .12 4.33 900 700 5 .51 4.72 750 600 3 .54 2 .95 Standard Depth-of-cut ap 1.5Dc ae Below 0 .02Dc 357 Endmill Series