324 Каталог SUMITOMO 2018 Инструмент металлорежущий Пластины Резцы Фрезы Сверла Стр.H26

Каталог SUMITOMO 2018 Инструмент металлорежущий Стр. H26 0324 Lab2u

Indexable Endmills Wavemill Series WEX Type Recommended Cutting Conditions WEX3000 Series Cutter: WEX30325E Insert: AXMT170508PEER - Cutting Data: ap = 5mm, ae = 16mm, dry 5mm 16mm H ISO Material HB Chipbreaker Coated Carbide „Diamond like Carbon" Coated Carbide ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000 Feed Rate (mm/tooth) 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,05 0,15 0,25 Cutting Speed vc (m/min) Unalloyed steel, <0, 15%C, annealed 125 G 400 370 350 370 350 330 350 330 310 , <0, 45%C, annealed , <0, 45%C, tempered 190 250 G G 300 250 270 220 250 200 270 220 250 200 230 180 250 200 230 180 210 160 P , <0, 75%C, annealed , <0, 75%C, tempered 270 300 G G 200 150 170 120 150 100 180 120 160 100 140 80 160 100 140 80 120 60 Low alloyed steel, annealed , tempered 180 275 G G 280 180 250 150 230 130 250 160 230 140 210 120 230 140 210 120 190 100 , tempered , tempered 300 350 G G 160 130 130 100 110 80 140 110 120 90 100 70 120 90 100 70 80 50 High alloyed and tool steel,annealed ,tempered 200 325 G G 250 130 220 100 200 80 220 100 200 80 180 60 200 80 180 60 160 40 M Stainless steel, ferritic/martensitic, annealed Martensitic, tempered 200 240 E EH 185 170 165 150 135 120 165 150 150 135 120 110 Austenitic, plunged 180 E 200 180 150 180 160 135 K Grey cast iron G 300 270 250 270 250 230 Nodular cast iron G 200 170 150 170 150 130 S High tempered resist. alloys, Fe based, annealed 300 E 50 30 45 25 , hardened 330 E 50 30 45 25 Aluminium alloy, Si < 13% S 1000 750 500 N Aluminium alloy, Si > 13% S 250 200 170 Copper alloy S 350 330 300 The above recommended cutting conditions are meant as a guide. Actual conditions will depend on the individual machine, work shape and clamping. They will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth and other factors. For groove milling, reduce the feed rate approximately 70% of the corresponding value shown above. I Recommended Values for Helical Milling and Ramping Helical Boring Recommended Values for Helical and Plunging < Min. Diameter 0D > Max. Diameter 0D Center uncut portion cannot be removed by traverse cutting with the same cutter. Center uncut portion can be removed by traverse cutting with the same cutter. Plunging Use at < a° Cutter External Diameter 0Dc WEX1000 (AXMT06...) WEX2000 (AX T12...) WEX3000 (AX DT17...) Helical Plunging Helical Plunging Helical Plunging Work Diameter Max. Ramping Angle Work Diameter Max. Ramping Angle Work Diameter Max. Ramping Angle Min. Max. Min. Max. Min. Max. 10 16,0 18,0 2°30' 12 20,0 22,0 1°45' 14 24,0 26,0 1°25' 25,0 27,0 1°40' 16 28,0 30,0 1°00' 29,0 31,0 1°20' 18 32,0 34,0 0°45' 33,0 35,0 1°10' 20 36,0 38,0 0°30' 37,0 39,0 1°00' 22 41,0 43,0 0°50' 25 46,0 48,0 0°30' 47,0 49,0 0°45' 44,5 48,0 1°30' 28 53,0 55,0 0°45' 50,5 54,0 1°10' 30 57,0 59,0 0°40' 54,5 58,0 1°10' 32 60,0 62,0 0°25' 61,0 63,0 0°35' 58,5 62,0 1°00' 35 64,5 68,0 0°50' 40 76,0 78,0 0°20' 77,0 79,0 0°25' 74,5 78,0 0°45' 50 96,0 98,0 0°15' 97,0 99,0 0°20' 94,5 98,0 0°30' 63 122,0 124,0 0°10' 123,0 125,0 0°15' 120,5 124,0 0°20' 80 154,5 158,0 0°15' 100 125 The above recommended values are for a nose radius of 0,8mm. H26