309 Каталог SUMITOMO 2018 Инструмент металлорежущий Пластины Резцы Фрезы Сверла Стр.H11

Каталог SUMITOMO 2018 Инструмент металлорежущий Стр. H11 0309 Lab2u

"METAL SLASH MILL MSX Type Recommended Cutting Conditions Coated Cutting Insert E ndmill Type (0 D) Shell Type (0D) Work 016 020 025 032 040 050 66 080 -100 Material Carbide Grade Speed vc (m/min) Cat. No. doc (mm) Feed rate (mm/tooth) doc (mm) Feed rate (mm/tooth) cm) om -o Feed rate (mm/tooth) doc (mm) Feed rate (mm/tooth) doc (mm) Feed rate (mm/tooth) doc (mm) Feed rate (mm/tooth) doc (mm) Feed rate (mm/tooth) WDMT 0603 0,8 0,8 0,8 0,8 0,8 0,8 - - - - - - - - General Steel (Below HB200) ACP200 100-150-200 IWDMT 0804 WDMT 1205 - - 1,0 1,0 1,0 1,2 1,0 1,2 1,2 1,4 1,2 1,4 1,2 1,4 - - WDMT 1406 - - - - - - - - 1,5 1,5 1,5 1,5 1,5 1,5 WDMT 0603 0,7 0,8 0,7 0,8 0,7 0,8 - - - - - - - - Alloy Steel (Below HRC45) ACP200 80-130-180 IWDMT 0804 - - 0,8 1,0 0,8 1,2 0,8 1,2 - - - - - - WDMT 1205 - - - - - - 1,0 1,4 1,0 1,4 1,0 1,4 - - WDMT 1406 - - - - - - - - 1,3 1,5 1,3 1,5 1,3 1,5 Stainless Steel X5CRNI1810, Others WDMT 0603 0,8 0,7 0,8 0,7 0,8 0,7 - - - - - - - - ACP300 80-120-150 IWDMT 0804 WDMT 1205 - - 1,0 0,8 1,0 0,8 1,0 1,2 0,8 1,2 1,2 1,2 1,2 1,2 - - WDMT 1406 - - - - - - - - 1,5 1,3 1,5 1,3 1,5 1,3 WDMT 0603 0,8 1,0 0,8 1,0 0,8 1,0 - - - - - - - - Cast Iron GG, GGG ACK300 100-150-200 IWDMT 0804 WDMT 1205 - - 1,0 1,2 1,0 1,4 1,0 1,2 1.4 1.5 1,2 1,5 1,2 1,5 - - WDMT 1406 - - - - - - - - 1,5 1,8 1,5 1,8 1,5 1,8 WDMT 0603 0,5 0,5 0,5 0,5 0,5 0,5 - - - - - - - - Hardened Steel ACK300 40-80-100 IWDMT 0804 - - 0,5 0,6 0,5 0,8 0,5 0,8 - - - - - - (Below HRC50) WDMT 1205 - - - - - - 0,6 1,0 0,6 1,0 0,6 1,0 - - WDMT 1406 - - - - - - - - 1,0 1,2 1,0 1,2 1,0 1,2 I Insert Cat. No. Max doc r The above recommended cutting conditions may require adjustment according to machine rigidity and work rigidity. WDMT 0603 1,0 1,5 The above figures are guidelines for use with the BT50 machine tool. I WDMT 0804 1,5 2,0 The above cutting conditions assume a tool overhang length of L/D=3 (i.e. overhang length is 3 times tool diameter) or less. WDMT 1205 2,0 2,0 When tool overhang is more than L/D=3 and less than or equal L/D=5, settings should be adjusted to approximately I WDMT 1406 2,5 2,0 70 to 80% of those indicated in the above cutting conditions (i.e. doc and Feed Rate). When tool overhang is more than L/D=5 and less than or equal L/D=8, settings should be adjusted to approximately 50 to 60% of those indicated in the above cutting conditions (i.e. doc and Feed Rate). Information for Programming For machine programming, please use the theoretical corner radius (R) shown in the list. Maximum depth (d) between theoretical radius and actual profile will be left on the finished surface, as shown below. Body Insert Theoretical Radius (R) Remaining Depth (d) MSX 08000 WDMT 0603 2,0 0,403 MSX 08000 WDMT 0804 2,5 0,593 d MSX 12000 WDMT 1205 3,0 1,030 MSX 14000 WDMT 1406 3,5 1,219 Plunging and Helical Boring Helical Boring WDMT0603ZDTR WDMT0804ZDTR WDMT1205ZDTR WDMT1406ZDTR do : max 1,0 do : max 1,5 doc : max 2,0 doc : max 2,5 0 Rampinq Helica boring Ramping Helica boring Ramping Helical boring Ramping Helical boring a min. max. a min. max. a min. max. a min. max. max. 0B 0B max. 0B 0B max. 0B 0B max. 0B 0B 16 6°00’ 21 31 17 5°00' 23 33 18 4°30' 25 35 20 3°30’ 29 39 7°30’ 25 38 22 3°00' 33 43 5°30' 29 42 25 2°00’ 39 48 4°00’ 35 48 28 3°00' 41 54 32 2°30’ 49 62 6°30’ 42 63 35 2°00' 55 68 5°00' 48 69 40 1°30’ 65 78 4°00’ 58 79 6°00’ 53 78 50 2°30’ 78 99 3°30’ 73 98 63 2°00’ 103 124 2°00’ 99 124 66 1°30' 109 130 1°45' 105 130 80 1°30’ 133 158 100 1°00’ 173 198 H11 Indexable Endmills