1028 Каталог KYOCERA 2019 Режущий инструмент для металлообработки на станках Стр.M58

Каталог KYOCERA 2019 Режущий инструмент по металлу Стр. M58 1028 Lab2u

M-FOUR (MEW) How to Mount Insert 1. Be sure to remove dust and chips from the insert mounting pocket. 2. Apply anti-seize compound on portion of taper and thread of clamp screw. (1) Attach the screw (magnetic head) to the front end of the wrench. (2) While lightly pressing the insert against the pocket walls, put the screw into the hole of the insert and tighten. (Ref. to Fig. 1.) Tighten M3 screws (SB-3065TRP) slightly inclined from the insert. (Ref. to Fig. 2.) surface of the insert. 3. When tightening the screw, make sure that the wrench is parallel to the screw. For recommended torque, Ref. to M54-M56 4. After tightening the screw, make sure that there is no clearance between the insert seat surface and the pocket floor of the holder or between the insert side surfaces and the pocket walls of the holder. If there is any clearance, remove the insert and mount it again according to the above steps. Recommended Cutting Conditions 45°-70° Lead Angle 75° Lead Angle 90788° Lead Angle High Feed Cutter Multi- Function B all-nose Radius Other Applications GM SM GH AM Workpiece Material Alloy Steel Austen itic Stainless Steel Martensitic Stainless Steel Precipitation Hardened Stainiess Steel Gray Cast Iron Nodular Cast Iron Ni-base Heat Resistant Alloy Titanium Alloys Alloy Steel Mold Steel Austen itic Stainless Steel Martensitic Stainless Steel Precipitation Hardened Stainiess Steel Ni-base Heat Resistant Alloy Titanium Alloys Alloy Steel Mold Steel Austen itic Stainless Steel Martensitic Stainless Steel Precipitation Hardened Stainiess Steel Gray Cast Iron Nodular Cast Iron Ni-base Heat Resistant Alloy Titanium Alloys Aluminum Alloy Feed Rate fz (ipt) Toolholder Description M EW0625-M EW0750 MEW16-MEW18 1002 0.004 0.006 1002 0.003 0.005 1002 0.003 0.005 1002 0.003 0.005 1002-0.003 i 1002 0.004 i 1002 0.003 0.005 1002 0.003 0.005 1002 0.003 0.005 1002 0.004 0.007 1002 0.003 0.005 1002 0.003 0.005 1002 0.003 i 1002 0.003 i 1002-0.003-0.005 1002 0.003 0.004 1002 0.003 0.005 1002 0.004 0.006 1002 0.003 0.005 1002 0.003 i 1002-0.003-1 1002-0.003-0.005 1002-0.003-0.006 1002-0.003-0.005 1002-0.003-0.005 M E W1000-M EW1500 MEW1500R-MEW3000R MEW20-MEW50 MEW032R-MEW080R 3.003-0.006-0.010 3.003-0.005-0.006 1003-0.005- 3.003-0.005- 1003-0.007- 3.003-0.006-1 3.003-0.005-0.006 3.003-0.005-0.007 3.003-0.004-0.006 3.003-0.004- 3.003-0.004- '.006 '.006 3.003-0.004-0.006 3.003-0.004-0.005 3.003-0.005-0.006 3.003-0.008-0.012 3.003-0.008-0.010 3.003-0.006-0.009 3.003-0.005- 3.003-0.005- 3.003-0.005- 3.003-0.009-0.012 3.003-0.007-0.010 3.003-0.005-0.006 3.003-0.006-0.010 Recommended Insert Grade Vc (sfm) MEGACOAT NANO PR1535 390-590-820 330-520-720 260-460-590 330-520-660 490-660-820 300-390-490 -100-160 -200-260 -590-820 -520-720 -460-590 520-' -390-490 -100-160 -200-260 -590-820 -520-720 -460-590 -520 i -390-490 -100-160 -200-260 PR1525 390-590- 330-520- 260-460-; 330-520-' 390-590- 330-520- 260-460-; 330-520-' 390-590-, 330-520- 260-460-; 330-520-' PR1510 390-590-820 330-490-660 100-160-230 100-160-230 390-590-820 330-490-660 100-160-230 CVD Coated Carbide CA6535 590-790-980 70-100-160 590-790-980 70-100-160 590-790-980 70-100-160 DLC Coated Carbide PDL025 % Bold numbers in the graph indicate the most recommended value of feed (f) Adjust cutting speed and feed rate according to the actual machining conditions Coolant is recommended for Ni-base heat resistant alloy and titanium alloy with MEW 660-2,950 :1st Recommendation it: 2nd Recommendation GW25 Applicable Chipbreaker Range (Shouldering) > LOMLHO .002 .004 .006.008 .010 .012 fz (ipt) > LOMU15 .002 .004 .006.008 .010 .012 fz (ipt) cCutting Conditio ns> Vc = 500 sfrn ae = 0D/2 Workpiece Material: 1049 Ramping, Helical Milling and Plunging 1. Available for vertical milling. 2. NOT available for ramping and helical milling, because interference between workpiece and insert may occur. M58 KyDEERa Visit us online at