197 Каталог HOFFMANN GROUP 2016 Слесарно-монтажный и измерительный инструмент Вер. 47 ENG Стр.197

Каталог HOFFMANN GROUP 2016 Слесарный и мерительный инструмент Стр. 197 0197 ENG Lab2u

Hoffmann Group 47 Single test pins steel Of high quality gauge steel, hardened (60 ±2 HRC) and tempered. Surface ground and lapped. From 0 1.5 mm engraved with the size. No. 483920 from 5.01 mm engraved with the size. 0.1 mm - 0.99 mm without chamfer. From 1.0 mm one end chamfered. Application: Degrease before use and grease after use. Note: When ordering, please additionally state the desired 0, e.g. No. 483900 size 510.08 or 483920 size 510.082. Type 02 01 o I 1 1 2 1 3 Single test pin tolerance dassl (93.85) (79.00) (26.14) (13.62) (11.68) (14.65) i 483910 Single test pin tolerance dass 2 (79.60) (55.04) (24.85) (10.99) (8.71) (11.93) Selection range nominal size Pitch Gauging pin length mm 0.1-0.19 mm 40 0.2 - 0.29 0.3-0.49 0.5 - 0.99 1-2.99 3-5.99 0.01 40 40 40 70 70 Type 4 I 5 I 6 I 7 1 8 9 1 Single test pin tolerance dassl (19.40) (26.14) (31.78) (41.88) (52.47) (61.97) i 483910 Single test pin tolerance dass 2 (14.61) (19.06) (23.27) (29.40) (34.55) (39.90) Selection range nominal size mm 6-9.99 10-11.99 12-13.99 14-15.99 16-18.99 19-20 Pitch mm 0.01 Gauging pin length mm 70 Individual test pins in increments of 0.001 mm ’ Measuring bore spacing/ reference area Position of bore Gearwheel measurement Type 0 j 1 I 2 1 3 1 4 1 5 1 6 1 7 1 8 9 1 iy TT m Single test pin tolerance dassl (57.82) (42.08) (42.08) (42.08) (47.62) (57.82) (70.88) (89.69) (98.41) (109.40) Selection range nominal size mm 0.301 -0.499 0.501 -0.999 1.001 -2.999 3.001 -5.999 6.001 -9.999 10.001 -11.999 12.001 -13.999 14.001 -15.999 16.001 -18.999 19.001 -19.999 Pitch mm 0.001 Gauging pin length mm 40 40 70 70 70 70 70 70 70 70 DIN 2269 H Cal Single test pins stainless and acid-resistant Test pin of stainless and acid-resistant material, hardened (58-62 HRC) and tempered. Surface ground and lapped. From 0 1.50 the dimension is marked on the sleeve; from 0 3.00 on the end face. From 0 1.00 mm, one end chamfered. Note: When ordering, please additionally state the desired 0, e. g. No. 483914 size 510.08. / Type 1 i 2 I 3 4 I 5 BfflffTl Individual stainless steel test pin tolerance dassl (18.71) (15.99) (20.20) (26.63) (35.64) Selection range nominal size mm 0.5-0.99 1-2.99 3-5.99 6-9.99 10-12 Pitch mm 0.01 Gauging pin length mm 40 70 70 70 70 DIN 2269 Single test pins carbide Test pin of carbide. Surface ground and lapped. From 0 5.01 marked with the size. Advantage: Twice as hard as gauge steel Corrosion-resistant Note: When ordering, please state the desired 0, e. g. No. 483916 size 3 4.35. Type 1 1 2 1 3 1 4 Individual carbide test pin tolerance dassl (54.85) (47.62) (54.05) (65.93) Selection range nominal size mm 0.5-0.99 1-2.99 3-5.99 6-9.99 Pitch mm 0.01 Gauging pin length mm 40 70 70 70 197