233 Каталог SUMITOMO 2018 Инструмент металлорежущий Пластины Резцы Фрезы Сверла Стр.F37

Каталог SUMITOMO 2018 Инструмент металлорежущий Стр. F37 0233 Lab2u

Insert Selection for ”Sumi-Grip” Series Parting-Off HddefS ”Sumi-Grip” Insert Ne OJ; 4C utral (N) , f 0,2 “PS r io WCF - N / R / L (General steel) WCF - N / R / L A Type A for hard to cut materials (Slow feed) ip WCF - N /R/ L B B I U Ordering No. Coated carbide a (mm) Ordering No. Coated carbide Uncoated carbide a (mm) Ordering No. Uncoated carbide a (mm) 7a AC830P AC225 A30 G10E Right hand (R) WCFN2 T 'J 2 WCFN 2 A 2 CM , r 0,2 WCFN 3 o 3 WCFN 3 A 3 WCFN 3 B 3 WCFR 3 o WCFR 3 A WCFR 3 B VS fadl WCFL 3 Cl WCFL 3 A WCFL 3 B 8° WCFN 4 Cl 4 WCFN 4 A O 4 WCFN 4 B 4 Left hand (L) WCFR 4 o WCFR4 A WCFR 4 B 3° 6si WCFL 4 o WCFL 4 A WCFL4B WCFN 5 Cl 5 WCFN 5 A 5 WCFN 5 B 5 M WCFR 5 Cl WCFR 5 A WCFR 5 B r 0,2 WCFL 5 o WCFL 5 A WCFL 5 B Very tough base material Structure of AC225 coated layer There is a multi layer coating which includes a 2 pm thick Al2O3 layer. It is very tough and resistant to adhesion wear. Insert Grade Map Applications and Features of Inserts Grade Ordering No. (Ex. a=3mm) Applications Features AC830P (AC3000) WCFN 3 General steel and high feed cutting (0,08 0,3/rev) Coated insert having excellent wear resistance with low cutting resistance AC225 WCFN 3A General steel and slow feed cutting (0,04 0,25/rev) soft steel, stainlessw steel Coated insert having excellent fracture toughness with good chip removal A30 WCFN 3A Hard to cut materials Equivalent to P30 G10E WCFN 3B Cast iron, aluminum alloy Equivalent to K10 with a small edge treatment Recommended Cutting Conditions Grade vc (m/min) f (mm/rev) General Steel Soft Steel Stainless Steel Die Steel Gray Cast Iron AC830P vc 100 - 220 120 - 250 80 - 200 60 - 150 - (AC3000) f 0,08 - 0,3 0,08 - 0,15 0,08 - 0,15 0,08 - 0,15 - AC225 vc 80 - 200 100 - 230 60 - 180 60 - 150 - f 0,04 - 0,25 0,04 - 0,2 0,04 - 0,2 0,04 - 0,2 - A30 vc 50 - 120 70 - 150 70 - 150 50 - 120 - f 0,05 - 0,2 0,04 - 0,15 0,04 - 0,15 0,04 - 0,15 - G10E vc - - - - 50 - 1 00 f - - - - 0,06 - 0,2 The recommended cutting conditions are valid when using the part-off tool with tool block type and shank type in the clamping system. F37 Grooving & Parting-Off