503 Каталог KYOCERA 2016 Металлорежущий инструмент для токарной обработки на станках Стр.H11

Каталог KYOCERA 2016 Токарные резцы с пластинами Стр. H11 0503 ENG Lab2u

CUT-OFF TOOLHOLDERS (SUB SPINDLE TOOLING) Applicable Inserts Classification of Usage W Light Interruption /1st Choice C Light Interruption / 2nd Choice Continuous / 1 st Choice O Continuous / 2nd Choice Carbon Steel / Alloy Steel Stainless Steel Non-ferrous Metals o Insert Right-handed Insert Shown Part Number Dimensions (in) W inch mm 0D Max 0d Angle MEGACOAT NANO in 0 d fl 1 JN TKFS127l 100-S 150-S 200-S TKFS127. 150-S 200-S Lead angle shows the angle when installed in the toolholder. As Fig.1 of H10 shows, the cutting diameter of the insert is measured when the lead edge passes 0.039" past the center line of part. Recommended Cutting Conditions Recommended Grade (Vc sfm) TKFS12 TKFS16 Workpiece Material Width Width MEGACOAT NANO MEGA COAT PVD Coated Carbide Carbide 0.039" (1.0mm) 0.059" (1.5mm) 0.079" (2.0mm) 0.059" (1.5mm) 0.079" (2.0mm) o z PR1425 PR1535 PR1225 PR1025 KW10 Feed Rate (ipr) Feed Rate (ipr) Carbon Steel 225-550 230-490 225-500 200-425 - 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 Alloy Steel 225-550 230-490 225-500 200-425 - 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 Stainless Steel 200-450 200-400 200-400 175-325 - 0.0004-0.0008 0.0004-0.0008 0.0004-0.0012 0.0004-0.0008 0.0004-0.0012 Wet Cast Iron - 175-325 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 Aluminum - 650-1475 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 0.0004-0.0012 Brass - 325-650 0.0004-0.0016 0.0004-0.0016 0.0004-0.0016 0.0004-0.0016 0.0004-0.0016 KTKF / KTKFS Selection Reference KTKF KTKFS > Both Right-hand and Left-hand types are applicable to gang tool post > Left-hand type is used during cut-off operations using sub spindle KTKFR Right-Hand Toolholder < Recom mendation> Use insert without lead angle. Not Using Sub Spindle Cut-off operation near main spindle side KTKFL Left-Hand Toolholder < Recom mendation> Use insert with lead angle to remove boss. Using Sub Spindle Cut-off operation near sub spindle side When machining workpiece with small diameter, use KTKFS to reduce overhang distance from the main spindle KTKFSR Right-Hand Toolholder R-Hand Long workpiece and more rigidity Cut-off operation near main spindle side L3 Dimension Sub Spindle Dia. 04Omm 22 (A type) 05Omm 26 (B type) KTKFSL Left-Hand Toolholder L-Hand Short workpiece and less rigidity Cut-off operation near main spindle side L3 Dimension Sub Spindle Dia. 04Omm 22 (A type) 05Omm 26 (B type) Inserts are sold in 10 piece boxes U.S. Stock U.S. Stock (R-hand Only) 0 U.S. Stock (L-hand Only) O World Express World Express (R-hand Only) World Express (L-hand Only) Kyocera H11