1307 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M151

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M151 1307 Lab2u

Fig.l dcsfms 04O DCON Fig.2 dcsfms DCO KW N \l i CBDF Ll l PR DAH DCCB -. KA X 5 DC Fig.3 DCSFMS 0125 Right hand tool holder only. ( For metric arbor ) The cutter bore diameter DCON is indicated in millimetre. Cutter Diameter DC 040 I ARBOR TYPE KAPR :90" GAMP:+14° +15” GAMF:+13"-+16” 050, 063 080 0100 0125 Set Bolt HFF08043H HSC10030H HSC12035H HSC16040H MBA20040H Geometry 0 a Type n Insert Radius Order Number Stock Number ofTeeth Dimensions(mm) I- 5 (kg) X s CL (mm) PM X 0. 2 OL Max. Allowable Revolution (min'1) ri) Ll. 1 >3 m o Q u. i DCON CBDP DAH DCSFMS KWW i DCCB R Clamp Screw Wrench Insert BXD4000-040A03RA 3 40 50 16 18 8.5 32 8.4 5.6 - 0.3 15 9° 29000 1 TS4SL TKY15W BXD4000-050A04RA 4 50 50 22 20 11 41 10.4 6.3 17 0.4 15 6° 24000 2 TS4SL TKY15W D CL 0.4 BXD4000-063A05RA 5 63 50 22 20 11 50 10.4 6.3 17 0.7 15 5° 21000 2 TS4SL TKY15W XDGT1550 3.2 BXD4000-080A05RA 5 80 50 27 23 13 60 12.4 7 20 1.1 15 3° 19000 2 TS4SL TKY15W PDOR-GOO BXD4000-100A06RA 6 100 63 32 26 17 70 14.4 8 26 2.0 15 3° 16000 2 TS4SL TKY15W BXD4000-125B07RA 7 125 63 40 40 42 80 16.4 9 56 2.8 15 2° 14000 3 TS4SL TKY15W BXD4000-040A03RB 3 40 50 16 18 8.5 32 8.4 5.6 - 0.3 15 9° 29000 1 TS4SL TKY15W BXD4000-050A04RB 4 50 50 22 20 11 41 10.4 6.3 17 0.4 15 6° 24000 2 TS4SL TKY15W 13 a. 4.0 BXD4000-063A05RB 5 63 50 22 20 11 50 10.4 6.3 17 0.7 15 5° 21000 2 TS4SL TKY15W XDGT1550 CO 5.0 BXD4000-080A05RB 5 80 50 27 23 13 60 12.4 7 20 1.1 15 3° 19000 2 TS4SL TKY15W PDOR-GOO BXD4000-100A06RB 6 100 63 32 26 17 70 14.4 8 26 2.0 15 3° 16000 2 TS4SL TKY15W BXD4000-125B07RB 7 125 63 40 40 42 80 16.4 9 56 2.8 15 2° 14000 3 TS4SL TKY15W Note 1) The maximum allowable revolutions are set to ensure tool and insert stability. Note 2) When using the tool at high spindle speeds, ensure that the tool and arbor are correctly balanced. 1 Clamp Torque (N m): TS4SL=4.0 2 RMPX : Max. Ramping Angle 3 WT : Tool Weight CAUTION FOR USE Only use the inserts and parts provided by Mitsubishi Materials with this tool. Use of the correct insert clamp screws is especially important to ensure overall tool safety. Do not use damaged or worn clamp screws. The maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the maximum allowable spindle speed. The maximum allowable spindle speeds for safety purposes are determined in accordance with IS015641 (Milling Cutters for high speed machining-Safety requirements). Table 1 Max. Allowable Revolution Cutting Edge Diameter DC(mm) 020 025 028 032 035 040 050 063 080 0100 0125 Max. Allowable Revolution (min-1) 15000 38000 35000 33000 31000 29000 24000 21000 19000 16000 14000 020mm with one tooth balancing is necessary to adjust sensitively. Even when operating under the maximum allowable spindle speed, if the spindle speed is equal to or higher than the values shown in table 2, it is recommended that the balance quality (with the arbor or milling chuck) conforms to G40 or betterbased on IS01940. It is also recommended to replace the clamp screws with new ones when changing inserts. Furthermore,ensure to use machines that are provided with safety measures in case of cutter breakage. Table 2 Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved Cutting Edge Diameter DC(mm) 020 025 028 032 035 040 050 063 080 0100 0125 Max. Allowable Revolution (mln-1) 15000 12000 10800 9500 8700 7600 6000 4800 3800 3000 2400 When setting the spindle speed, take into consideration the maximum allowable spindle speed of the arbor or milling chuck. Use the specified set bolt when using the arbor type with through coolant. The inserts have sharp cutting edges and handling them with bare hands may cause injuries. Always wear safety gloves when handling the indexable inserts. SPARE PARTS >Q001 TECHNICAL DATA > R001 M151 INDEXABLE MILLING