1288 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M132

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M132 1288 Lab2u

INDEXABLE MILLING INDEXABLE MILLING I Ramping I Helical Milling I Ramping Helical Milling APMX (P) t i r> i i i i V DC Hole Refer to the table below for cutting conditions. For feed per tooth and cutting speed, follow the cutting conditions for slot milling. Diameter (DH) (DH) DC (mm) RE (mm) Rampina Helical Millina (Blind Hole, Flat Bottom) Helical Milling (Through Hole) RMPX L (mm) DH max. (mm) Pmax. (mm) DH min. (mm) Pmax. (mm) DH min. (mm) P max. (mm) 0.2 1.06“ 595 78.8 2.3 72.7 1.9 66.5 1.5 0.4 1.06" 595 78.4 2.2 72.7 1.9 66.5 1.5 0.8 1.06" 595 77.6 2.2 72.7 1.9 66.5 1.5 1 1.06“ 595 77.2 2.2 72.7 1.9 66.5 1.5 40 1.2 1.06” 595 76.8 2.1 72.7 1.9 66.5 1.5 1.6 1.06" 595 76 2.1 72.7 1.9 66.5 1.5 2 1.06“ 595 75.2 2 72.7 1.9 66.5 1.5 2.4 1.06” 595 74.4 2 72.7 1.9 66.5 1.5 3 1.06" 595 73.2 1.9 72.7 1.9 66.5 1.5 3.2 1.06' 595 72.8 1.9 72.7 1.9 66.5 1.5 0.2 0.79" 798 98.8 2.1 92.7 1.8 86.5 1.6 0.4 0.79" 798 98.4 2.1 92.7 1.8 86.5 1.6 0.8 0.79" 798 97.6 2.1 92.7 1.8 86.5 1.6 1 0.79" 798 97.2 2 92.7 1.8 86.5 1.6 50 1.2 0.79" 798 96.8 2 92.7 1.8 86.5 1.6 1.6 0.79” 798 96 2 92.7 1.8 86.5 1.6 2 0.79" 798 95.2 2 92.7 1.8 86.5 1.6 2.4 0.79“ 798 94.4 1.9 92.7 1.8 86.5 1.6 3 0.79“ 798 93.2 1.9 92.7 1.8 86.5 1.6 3.2 0.79" 798 92.8 1.9 92.7 1.8 86.5 1.6 0.2 0.6” 1051 124.8 2 118.7 1.8 112.5 1.6 0.4 0.6" 1051 124.4 2 118.7 1.8 112.5 1.6 0.8 0.6” 1051 123.6 2 118.7 1.8 112.5 1.6 1 0.6" 1051 123.2 2 118.7 1.8 112.5 1.6 63 1.2 0.6“ 1051 122.8 2 118.7 1.8 112.5 1.6 1.6 0.6” 1051 122 1.9 118.7 1.8 112.5 1.6 2 0.6" 1051 121.2 1.9 118.7 1.8 112.5 1.6 2.4 0.6“ 1051 120.4 1.9 118.7 1.8 112.5 1.6 3 0.6" 1051 119.2 1.9 118.7 1.8 112.5 1.6 3.2 0.6“ 1051 118.8 1.8 118.7 1.8 112.5 1.6 0.2 0.45“ 1401 158.8 1.9 152.6 1.8 146.5 1.6 0.4 0.45“ 1401 158.4 1.9 152.7 1.8 146.5 1.6 0.8 0.45” 1401 157.6 1.9 152.7 1.8 146.5 1.6 1 0.45" 1401 157.2 1.9 152.7 1.8 146.5 1.6 80 1.2 0.45” 1401 156.8 1.9 152.7 1.8 146.5 1.6 1.6 0.45” 1401 156 1.9 152.7 1.8 146.5 1.6 2 0.45” 1401 155.2 1.9 152.7 1.8 146.5 1.6 2.4 0.45 1401 154.4 1.8 152.7 1.8 146.5 1.6 3 0.45 1401 153.2 1.8 152.7 1.8 146.5 1.6 3.2 0.45 1401 152.8 1.8 152.7 1.8 146.5 1.6 Note 1) When machining a highly ductile work material with the ramping angles in the table above, chips may be elongated. Shows the distance until a maximum depth of cut of 11 mm is achieved at the maximum ramping angle L (= 11/tan a). M132