1287 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M131

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M131 1287 Lab2u

I Ramping I Helical Milling I Ramping I Helical Milling APMX (p) I V - DC Hole Refer to the table below for cutting conditions. For feed per tooth and cutting speed, follow the cutting conditions for slot milling. Diameter (DH) (DH) DC (mm) RE (mm) Rampina Helical Millina (Blind Hole, Flat Bottom) Helical Milling (Through Hole) RMPX L (mm) DH max. (mm) Pmax. (mm) DH min. (mm) Pmax. (mm) DH min. (mm) Pmax. (mm) 0.2 2.13° 296 49 2.8 42.7 2.1 36.9 1.4 0.4 2.13" 296 48.6 2.8 42.7 2.1 36.9 1.4 0.8 2.13" 296 47.8 2.7 42.7 2.1 36.9 1.4 1 2.13" 296 47.4 2.6 42.7 2.1 36.9 1.4 25 1.2 2.13" 296 47 2.6 42.7 2.1 36.9 1.4 1.6 2.13" 296 46.2 2.5 42.7 2.1 36.9 1.4 2 2.13" 296 45.4 2.4 42.7 2.1 36.9 1.4 2.4 2.13" 296 44.6 2.3 42.7 2.1 36.9 1.4 3 2.13" 296 43.4 2.2 42.7 2.1 36.9 1.4 3.2 2.13" 296 43 2.1 42.7 2.1 36.9 1.4 0.2 1.77" 356 55 2.6 48.7 2 42.7 1.4 0.4 1.77" 356 54.6 2.6 48.7 2 42.7 1.4 0.8 1.77" 356 53.8 2.5 48.7 2 42.7 1.4 1 1.77" 356 53.4 2.5 48.7 2 42.7 1.4 28 1.2 1.77° 356 53 2.4 48.7 2 42.7 1.4 1.6 1.77° 356 52.2 2.4 48.7 2 42.7 1.4 2 1.77” 356 51.4 2.3 48.7 2 42.7 1.4 2.4 1.77" 356 50.6 2.2 48.7 2 42.7 1.4 3 1.77" 356 49.4 2.1 48.7 2 42.7 1.4 3.2 1.77" 356 49 2 48.7 2 42.7 1.4 0.2 1.61” 392 59 2.6 52.7 2 46.6 1.5 0.4 1.61" 392 58.6 2.5 52.7 2 46.6 1.5 0.8 1.61” 392 57.8 2.5 52.7 2 46.6 1.5 1 1.61” 392 57.4 2.4 52.7 2 46.6 1.5 30 1.2 1.61" 392 57 2.4 52.7 2 46.6 1.5 1.6 1.61” 392 56.2 2.3 52.7 2 46.6 1.5 2 1.61” 392 55.4 2.2 52.7 2 46.6 1.5 2.4 1.61“ 392 54.6 2.2 52.7 2 46.6 1.5 3 1.61” 392 53.4 2.1 52.7 2 46.6 1.5 3.2 1.61“ 392 53 2 52.7 2 46.6 1.5 0.2 1.47” 429 63 2.5 56.7 2 50.6 1.5 0.4 1.47“ 429 62.6 2.5 56.7 2 50.6 1.5 0.8 1.47" 429 61.8 2.4 56.7 2 50.6 1.5 1 1.47" 429 61.4 2.4 56.7 2 50.6 1.5 32 1.2 1.47“ 429 61 2.3 56.7 2 50.6 1.5 1.6 1.47" 429 60.2 2.3 56.7 2 50.6 1.5 2 1.47” 429 59.4 2.2 56.7 2 50.6 1.5 2.4 1.47” 429 58.6 2.1 56.7 2 50.6 1.5 3 1.47“ 429 57.4 2.1 56.7 2 50.6 1.5 3.2 1.47” 429 57 2 56.7 2 50.6 1.5 0.2 1.28” 493 69 2.4 62.8 1.9 56.6 1.5 0.4 1.28" 493 68.6 2.4 62.8 1.9 56.6 1.5 0.8 1.28° 493 67.8 2.3 62.8 1.9 56.6 1.5 1 1.28° 493 67.4 2.3 62.8 1.9 56.6 1.5 35 1.2 1.28" 493 67 2.2 62.8 1.9 56.6 1.5 1.6 1.28” 493 66.2 2.2 62.8 1.9 56.6 1.5 2 1.28" 493 65.4 2.1 62.8 1.9 56.6 1.5 2.4 1.28“ 493 64.6 2.1 62.8 1.9 56.6 1.5 3 1.28" 493 63.4 2 62.8 1.9 56.6 1.5 3.2 1.28" 493 63 2 62.8 1.9 56.6 1.5 Note 1) When machining a highly ductile work material with the ramping angles in the table above, chips may be elongated. Shows the distance until a maximum depth of cut of 11 mm is achieved at the maximum ramping angle L (= 11/tan a). M131 INDEXABLE MILLING