1073 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.K041

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. K041 1073 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Shoulder milling (L/D=3) Other than the L/D = 3, use following recommended cutting conditions by multiplying the K003 page correction factor by overhang length. (mm) LU D o CO m Work Material Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloy AISI 304, AISI410 AISI 316, AISI 304LN, AISI 316LN, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Dia. DC Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cul ae 10 12 16 20 25 200 200 200 200 200 6400 5300 4000 3200 2500 0.07 0.085 0.088 0.1 0.1 2700 2700 3500 3800 3000 10 12 16 20 25 1 1.2 0.6 0.8 1 150 150 150 150 150 4800 4000 3000 2400 1900 0.07 0.085 0.088 0.1 0.1 2000 2000 2600 2900 2300 10 12 16 20 25 1 1.2 0.64 0.8 1 100 100 100 100 100 3200 2700 2000 1600 1300 0.07 0.085 0.088 0.1 0.1 1300 1400 1800 1900 1600 10 12 16 20 25 1 1.2 0.6 0.8 1 cc LU a. Depth of cut ap Work Material Depth of cut Heat resistant alloys lnconel718 Dia. DC Cutting Speed (m/mln) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae 10 40 1300 0.033 260 10 0.5 12 40 1100 0.035 230 12 0.6 16 40 800 0.038 300 16 0.6 20 40 640 0.04 310 20 0.8 25 40 510 0.04 240 25 1 ap I o 0 z 1 o 3 o Di Note 1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut, Note 4) If the machining radius at the corner is the same as the tool radius when using the head with more than 10 flutes, please set the depth of cut and feed rate to half of the above. a m K041