1079 Каталог KYOCERA 2019 Режущий инструмент для металлообработки на станках Стр.M109

Каталог KYOCERA 2019 Режущий инструмент по металлу Стр. M109 1079 Lab2u

MSR MSR-BT50 WF0 E E yT" i Q -\BT-50 Arbor m 101.8mm o APMX L 38m st- SssBfel - 1 i ) \ 01 OOmm / -SEE \BT-50 Arbor APMX 38r LF nm 101.8mm Fig-1 Fig.2 Toolholder Dimensions Part Number o No. of Inserts No. of Flutes No. of Stages Dimensions (mm) Rake Angle Drawing Weight (kg) DC LF APMX A.R. R.R. MSR 063R-BT50-4 16 4 4 63 160 90 Fig.1 5.7 063R-BT50-5 20 5 180 111 +9° -8° Fig.2 6.2 080R-BT50-4 16 4 4 80 160 90 Fig.1 6.9 080R-BT50-5 20 5 180 111 Fig.2 7.4 100R-BT50-4 24 6 4 100 160 90 +9° -5° Fig.1 9.6 100R-BT50-5 30 5 180 111 Fig.2 10.5 O m A SS A 1 33 Q 33 T3 S8 O cz I- 33 O m = O S o > O 33 Z Q B Spare Parts Part Number Spare Parts Clamp Screw Wrench Shim Clamp Screw Wrench Anti-Seize Compound u & u MSR 063R-OC SB-60120TR TT-25L - - - P-37 MSR 080R-OC i 315R-OC MAP-2506 SB-40140TR DT-15 For Insert Clamp For Shim Clamp MSR 063R-BT50-O SB-60120TR TT-25L - - - P-37 MSR 080R-BT50-O MAP-2506 SB-40140TR DT-15 100R-BT50-O For Insert Clamp For Shim Clamp O cz -H o > H Coat Anti-Seize Compound (P-37) thinly on portion of taper and thread prior to installation. Applicable Inserts Applicable Inserts M18 Part Number 13 gv is 3-Notch 4-Notch 3-Notch / Low Cutting Force 4-Notch / Low Cutting Force MSR... MSR...M APMT 2506OOER-NB3 APMT 2506OOER-NB4 APMT 250616ER-NB3P APMT 250616ER-NB4P Custom-Ordered Left-hand Cutter APMT 250616EL-NB3 APMT 250616EL-NB4 - - K Caution when Installing Notched Inserts It is important to install the appropriate notched insert into the correct position. Failure to do so may result in damage to the toolholder body. The appropriate insert is marked on the pocket of the cutter body. (3) is for APMT250600ER-NB3 (4) is for APMT250600ER-NB4 Recommended Cutting Conditions M110-M111 (No. of Inserts - Example) Part Number No. of Inserts No. of Flutes No. of Inserts Notched NB3 NB4 MSR 1 00R-1 6 6 3 3 100R-2 12 6 6 1 00R-4 24 12 12 Caution when Installing the Insert with Corner-R(RE) 4.0 When installing the insert with corner-radius 4.0mm, additional modifications for the body will be necessary. Refer to the table below for the recommended modifications. Insert Corner-R (RE) Additional Processing Dimension to Body Corner (mm) 4.0 R2.0 Round- chamfer additional processing is recommended. When applying chamfer, do not cut away too much. Body Corner N Pre-processing \ Large Corner-R(RE) Post-processing : Standard Item A : Phaseout Item (will be removed from next catalog) Contact your local Kyocera sales engineer to upgrade old products to new technology (Customer Service) - Option 1 (Technical Support) - Option 2 Visit us online at Kyocera M109