817 Каталог KYOCERA 2017 Инструмент сборный и монолитный для станков Стр.M67

Каталог KYOCERA 2017 Инструмент режущий Стр. M67 0817 Lab2u

Ramping, Helical milling and Vertical milling (Plunging) 1. Available for vertical milling (plunging). 2. NOT available for ramping and helical milling, because interference between workpiece and insert may occur. Vertical Milling (Plunging) Insert Description Обозначение Max. Width of Cut (ae) LOMUIO 5mm LOMU15 7mm Cutting Performance Description Обозначение MEW16...-10 MEW18...-10 MEW20...-10 i MEW50...-10 MEW20-S20 -10-150-2T MEW25-S25 -10-170-2T (Long Shank) MEW032R...-10 MEW063R.-10 Shouldering (Cutting width ae = 0D/2) 0.15 66.2 66.255 f;:(mm666 6.15 6.2 6.25 fz(mm/6) 6.15 6.2 6.25 fz(mm/t) Slotting O.K 0.2 0.25 fpmmm/t) 6.15 6.2 6.25 fz(mm/t) 10 8 "e 6 m1226 06 6I: . j of-1-. 2 °i- : i :-'62 - mm44646 : i f ) 6.15 6.2 6.25 fz(mm/t) 20 4 : XH-1 'E 6 fo ..h; 2 i - f : -i - 6 ; 6.1 6.15 6.2 6.25 6.1 6.15 6.2 6.25 fz(mm/t ) fpmm/t ) Description Обозначение MEW25...-15 i MEW50...-15 MEW040R 15 i MEW080R 15 Shouldering (Cutting width ae = 0D/2) i’4 6..5 6.2 6.25 fzfmm/t) 6.15 0.2 6.25 fz(mm/t ) Slotting Vc=180m/min GM Chipbreaker Стружколом сменной пластины Workpiece Material Обрабатываемый материал : S50C Overhang Length 1. End mill: Same length as I of the dimension 2. Face mill: H of the dimension + minimum overhang length of the arbor Case Studies SS400 Construction machine part Vc=250m/min apxae=4x20mm fz=0.14mm/t(Vf=1,350mm/min) Wet MEW32-S32-10-4T(4 inserts) LQMU100408ER-GM(PR1525) PR1525 Chip Evacuation Rate =108cc/min Competitor A (Positive Cutter) Chip Evacuation Rate =72cc/min MEW showed stable milling without chattering at higher feed, improving the machining efficiency by 150%. Burrs are prevented and excellent surface finish is achieved. (Evaluation by the user) 15-5PH (42HRC) , 130 , 25 Aircraft Part Vc=180m/min apxae=2x25mm fz=0.1mm/t(Vf=716mm/min) Wet MEW32-S32-10-4T(4 inserts) LQMU100408ER-GM(PR1525) PR1525 Chip Evacuation Rate = 35.8cc/min (Further Machining Possible) Competitor B (Positive Cutter) Chip Evacuation Rate = 26.8cc/min (Unable to continue machining) No chattering and more stable milling is possible with MEW. Despite the milling difficulty because of the properties of the material, PR1525 kept good cutting edge form, minimizing wear and adhesion. (Evaluation by the user) M67 Milling