466 Каталог KYOCERA 2017 Инструмент сборный и монолитный для станков Стр.G105

Каталог KYOCERA 2017 Инструмент режущий Стр. G105 0466 Lab2u

GA Inserts (Molded Chipbreaker) Workpiece Material Обрабатываемый материал Recommended Insert Grades Cutting Speed Vc (m/min) Скорость резания (м/мин) (1) f for Grooving (mm/rev) (2) f for Turning (mm/rev) (3) ap for Turning (mm) Remarks Примечания Cermet CVD Coae Caibide PVD Coated Carbide Carbide TN60 TN90 TC40N TC60M CR9025 PR630 PR930 KW10 GA 30 GA 40 GA 50 Carbon Steel 130 200 80 180 (1)0.06 0.18 (2)0.05 0.15 (3)Max. 0.8 C i-O OO COLOX ooro t C .CO 5 .2.2.3 OO COLOX ooro Coolant Alloy Steel 100 180 80 160 52 .1.1.3 00 0. COLOX ooro t C .CO 85 .1.1.5 oo o COLOX ooro o o 5 .C .CO 28 .2.1.8 oo o COLOX ooro o o 5 .C .CO Stainless Steel 60 130 8 .1.0.8 00 0. COLOX OOCB t C .CO 8 .1.0.8 do o COLOX OOCB o o 5 .C .CO 2 .1.1.2 00 1. COLOX oocc .C .CO : 1st Recommendation : 2nd Recommendation GIA Inserts (Molded Chipbreaker) Workpiece Material Обрабатываемый материал Recommended Insert Grades Cutting Speed Vc (m/min) Скорость резания (м/мин) (1) f for Grooving (mm/rev) (2) f for Turning (mm/rev) (3) ap for Turning (mm) Remarks Примечания Cermet CVD Cc lBd Caibde PVD Coated Carbide Carbide TN60 TN90 TC40N TC60M CR9025 PR630 PR930 KW10 GIA 30 GIA 40 GIA 50 Carbon Steel 60 120 60 120 88 .0.0.3 00 0. "tC X ooro t C .CO (1)0.04 0.09 (2)0.02 0.08 (3)Max. 0.4 (1)0.05 0.1 (2)0.05 0.08 (3)Max. 0.5 Coolant Alloy Steel 60 100 60 100 ooco do o >< ooro .C .CO OO-ct dd o >< ooro o o 5 .C .CO 88 .0.0.5 dd d LOLOx ooro o o 5 t C .CO Stainless Steel 60 80 ooco 00 0. OOCB .C .CO OO-cf dd o OOCB o o 5 .C .CO 88 .0.0.5 dd o LOLOX OOCB .C .CO PSG-S (Tip-Bars Workpiece Material Обрабатываемый материал Recommended Insert Grades Cutting Speed Vc (m/min) Скорость резания (м/мин) PSG05 PSG06 PSG07 PSG08 Remarks Примечания PVD Coated Carbide Carbide PR930 KW10 f (mm/rev) Carbon Steel 30 100 0.03 0.05 Coolant Stainless Steel 30 80 0.02 0.03 Non-ferrous Metals 300 0.05 0.08 : 1st Recommendation : 2nd Recommendation Note for using the grooving tip-bars PSG-S type How to Install Small dia. internal grooving requires accurate installation because an error of insert height or angle can affect the machining precision. When installing, set the cutting edge higher than the center line as shown in the Table 1. The cutting edge of all the PSG-S type tip-bars is designed to be higher than the center line. (L4 of Tip-Bars dimension) FMM/FMN : 1st Recommendation Workpiece Material Обрабатываемый материал Recommended Insert Grades Cutting Speed Vc (m/min) Скорость резания (м/мин) Face Grooving (FMM / FMN) Turning (FMM) Remarks Примечания Cermet CVD Med CaiMt PVD Coated Carbide Carbide Edge Width (mm) Edge Width (mm) TN90 CR9025 PR915 PR930 PR905 KW10 3.0 4.0 5.0/6.0 3.0 4.0 5.0/6.0 f (mm/rev) Carbon Steel 100 220 80 200 80 200 80 200 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Coolant Alloy Steel 80 200 70 180 70 180 70 180 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Stainless Steel 70 160 60 150 60 150 60 150 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Cast Iron 80 180 70 150 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Aluminum Alloys 200 500 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Brass 100 200 0.03 0.05 0.03 0.08 0.05 0.10 0.05 0.10 0.05 0.25 0.10 0.30 Set the feed rate 1/100 of edge width on the first groove and check chip evacuation. : 1st Recommendation : 2nd Recommendation FMN type Inserts are only for Deep Grooving, and when used for turning, set to ap=0.2mm and under. Ref. to the notes below for turning conditions. ap and f of FMM Recommended Cutting Conditions Рекомендованные режимы резания на станках ap (MAX.) (mm) under 50% of Edge Width f (MAX.) (mm/rev) under 3 5% of Edge Width 1 ap<0.5w f<0.03(Min.) 0.05(Max.)w ap x f should be as follows. LoadM 3.0 4.0 5.0 6.0 ap x f 0.09 0.14 0.25 0.36 ap x f<0.01w2 G105 Grooving