456 Каталог ISCAR 2017 Токарный металлорежущий инструмент и инструментальная оснастка Стр.452

Каталог ISCAR 2017 Токарный инструмент и оснастка Стр. 452 0456 ENG Lab2u

FACE GROOVING CUTGniP CGFG 51-P8 Blades for Face Machining Carrying 8 mm Inserts Designation W D1 min(1) D1 max(2) T max-a B1 h1 l1 H2 A2 / CGFG 51-180R/L-P8 8.00 180.0 240.0 70.00 52.6 45.0 200.00 60.0 27.5 SR M4-2052 HW 3.0 CGFG 51-240R/L-P8 8.00 240.0 320.0 80.00 52.6 45.0 210.00 70.0 26.0 SR M4-2052 HW 3.0 CGFG 51-320R/L-P8 8.00 320.0 440.0 90.00 52.6 45.0 220.00 80.0 24.5 SR M4-2052 HW 3.0 CGFG 51-440R/L-P8 8.00 440.0 700.0 100.00 52.6 45.0 230.00 90.0 22.5 SR M4-2052 HW 3.0 CGFG 51-700R/L-P8 8.00 700.0 1500.0 120.00 52.6 45.0 250.00 100.0 20.0 SR M4-2052 HW 3.0 For user guide, see pages 460-470 (1) Minimum penetration diameter (2) Maximum penetration diameter For inserts, see pages: GIMF (244) GIMM 8CC (454) GIMY (245) GIMY (full radius) (246) GIMY-F (247) GIPY (255) For holders, see pages: SGTBK (473) SGTBU/SGTBN (472) CUTGniP GIFG-E (W=8) Inserts for Deep Face Grooving and Turning Dimensions Tough Hard Recommended Machining Data Designation W±0.02 R±°.°5 D1 min Tmax-a M IC635 0 2 IC f face-groove (mm/rev) GIFG 8.00E-0.80 8.00 0.80 50.0 25.00 6.00 0.15-0.25 GIFG 8.00E-1.20 8.00 1.20 50.0 25.00 6.00 0.15-0.25 For cutting speed recommendations, see pages 464-465 For tools, see pages: GAFG-R/L-8 (451) GHFG-R/L-8 (450) GHFGR/L-8 (450) CUTGniP GIF-E (W=8,10) Precision Double-Ended Inserts for Grooving and Turning rf J w Dimensions Tough Hard Recommended Machining Data Designation W±0.02 R R±toler M Tmax-r IC830 IC8250 IC808 0 2 IC IC5010 IC428 IC806 0 8 IC ap (mm) f turn (mm/rev) f groove (mm/rev) GIF 8.00E-0.40 8.00 0.40 0.030 6.00 27.00 0.50-4.80 0.29-0.48 0.18-0.31 GIF 8.00E-0.80 8.00 0.80 0.050 6.00 27.00 1.00-4.80 0.32-0.56 0.18-0.34 GIF 8.00E-1.20 8.00 1.20 0.050 6.00 27.00 1.45-4.80 0.32-0.62 0.18-0.34 GIF 10.00E-0.80 10.00 0.80 0.050 8.00 27.00 1.00-6.00 0.35-0.65 0.22-0.40 GIF 10.00E-1.20 10.00 1.20 0.050 8.00 27.00 1.45-6.00 0.35-0.72 0.22-0.40 Dmin for internal machining = 65 mm For cutting speed recommendations and user guide, see pages 460-470 For tools, see pages: C -GHDR/L (233) CGHN-8-10D (244) GADR/L-8 (243) GADR/L-JHP (243) GAFG-R/L-8 (451) GHDR/L (long pocket) (240) GHDR/L-JHP (long pocket) (241) GHFG-R/L-8 (450) GHFGR/L-8 (450) GHIR/L (W=7.0-8.3) (301) 452 ISCAR