440 Каталог ISCAR 2017 Токарный металлорежущий инструмент и инструментальная оснастка Стр.436

Каталог ISCAR 2017 Токарный инструмент и оснастка Стр. 436 0440 ENG Lab2u

FACE GROOVING fSUKACE HGHR/L-3 Integral Holders for Face Grooving and Turning, Dmin. 12 mm Designation h b W T max-a h4 f D1 min(1) D1 max(2) l1 l2 H2 A1 HGHR/L 1010-12-3T6 10.0 10.0 3.00 6.00 2.0 9.5 12.0 16.0 120.00 19.0 19.0 13.70 SR 76-1400 T-20/3 HGHR 1010-16-3T6 10.0 10.0 3.00 6.00 2.0 9.5 16.0 25.0 120.00 19.0 19.0 12.80 SR 76-1400 T-20/3 HGHR/L 1212-12-3T6 12.0 12.0 3.00 6.00 - 11.0 12.0 16.0 120.00 19.0 19.0 15.70 SR 76-1400 T-20/3 HGHR 1212-16-3T6 12.0 12.0 3.00 6.00 - 11.0 16.0 25.0 120.00 19.0 19.0 14.80 SR 76-1400 T-20/3 HGHR/L 1616-12-3T6 16.0 16.0 3.00 6.00 - 15.0 12.0 16.0 120.00 19.0 21.0 19.70 SR 76-1400 T-20/3 HGHR/L 1616-16-3T6 16.0 16.0 3.00 6.00 - 15.0 16.0 25.0 120.00 19.0 21.0 18.80 SR 76-1400 T-20/3 HGHR/L 2020-12-3T6 20.0 20.0 3.00 6.00 - 20.0 12.0 16.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3 HGHR/L 2020-16-3T6 20.0 20.0 3.00 6.00 - 20.0 16.0 25.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3 HGHR/L 2525-12-3T6 25.0 25.0 3.00 6.00 - 25.0 12.0 16.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3 HGHR/L 2525-16-3T6 25.0 25.0 3.00 6.00 - 25.0 16.0 25.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3 HGN GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders. For user guide, see pages 460-470 Minimum penetration diameter Maximum penetration diameter For inserts, see pages: GRIP (229) GRIP (full radius) (230) HGN-C (386) HGN-J (386) HGN-UT (387) HGPL (449) No limitation for widening groove toward or away from center, except for the following tools: HGHR/L...-12-3T6 D d 12.0 4.0 13.0 1.0 13.5 0 tsuncE HFHR/L-3T Integral Holders for Facing, Dmin. 25 mm Designation W Tmax-a h b l1 f F1 D1 min<2) D1 max(3) l2 H2 / s' HFHR/L 20-25-3T12 3.00 12.00 20.0 20.0 140.00 20.5 5.3 25.0 30.0 38.0 28.0 SR M6X16 DIN912 HW 5.0 HFHR/L 20-30-3T12 3.00 12.00 20.0 20.0 140.00 20.5 5.3 30.0 38.0 38.0 29.0 SR M6X16 DIN912 HW 5.0 HFHR/L 20-38-3T12 3.00 12.00 20.0 20.0 140.00 20.5 5.3 38.0 48.0 38.0 30.0 SR M6X16 DIN912 HW 5.0 HFHR/L 20-48-3T12 3.00 12.00 20.0 20.0 140.00 20.5 5.3 48.0 60.0 38.0 30.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-25-3T12 3.00 12.00 25.0 25.0 150.00 25.5 5.3 25.0 30.0 38.0 33.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-30-3T12 3.00 12.00 25.0 25.0 150.00 25.5 5.3 30.0 38.0 38.0 34.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-38-3T12 3.00 12.00 25.0 25.0 150.00 25.5 5.3 38.0 48.0 38.0 35.0 SR M6X16 DIN912 HW 5.0 HFHR/L 20-60-3T22 (1) 3.00 22.00 20.0 20.0 140.00 20.5 - 60.0 75.0 40.0 31.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-48-3T22 (1) 3.00 22.00 25.0 25.0 150.00 25.5 - 48.0 60.0 40.0 36.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-60-3T22 (1) 3.00 22.00 25.0 25.0 150.00 25.5 - 60.0 75.0 40.0 36.0 SR M6X16 DIN912 HW 5.0 HFHR/L 20-75-3T25 (1) 3.00 25.00 20.0 20.0 140.00 20.5 - 75.0 100.0 43.0 31.0 SR M6X16 DIN912 HW 5.0 HFHR/L 25-75-3T25 (1) 3.00 25.00 25.0 25.0 150.00 25.5 - 75.0 100.0 43.0 36.0 SR M6X16 DIN912 HW 5.0 For user guide, see pages 460-47 (1) For deep face grooving only. (2) Minimum penetration diameter (3) Maximum penetration diameter For inserts, see pages: HFPR/L (447) HFPR/L (full radius) (448) No limitation for widening groove toward or away from center, except for the following tools: HFHR/L-:-25-3T12 HFHR/L-:-25-4T12 D d 25 5 26 2 >27 0 D d 25 1 >26 0 HFHR/L-:-29-4T12 D d 29 1 >46 0 Limitation of widening toward center (d) depends on the major D 7> diameter (D) as per chart. d 436 ISCAR