1305 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M149

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M149 1305 Lab2u

Blind holes, HELICAL CUTTING RAMPING/HELICAL CUTTING (ALUMINIUM ALLOY) (DH) Type DC (mm) RE (mm) BS (mm) Helical Cutting (Blind Hole, Flat Bottom) 2 DH max. (mm) P max. (mm) 3 DH min. (mm) Pmax. (mm) 0.8 2 61.9 20 58.3 20 1.6 1.2 60.3 19 58.3 19 2 0.8 59.5 18 58.3 18 oz 2.4 0.4 58.7 18 58.3 18 3 0.8 57.5 17 56.2 17 3.2 0.6 57.1 17 56.2 17 0.8 2 77.9 20 74.3 20 1.6 1.2 76.3 19 74.3 19 a n 2 0.8 75.5 18 74.3 18 4U 2.4 0.4 74.7 18 74.3 18 3 0.8 73.5 17 72.2 17 3.2 0.6 73.1 17 72.2 17 0.8 2 97.5 20 94.1 20 1.6 1.2 95.9 19 94.1 19 2 0.8 95.1 18 94.1 18 ou 2.4 0.4 94.3 18 94.1 18 3 0.8 93.1 17 92.1 17 3.2 0.6 92.7 17 92.1 17 0.8 2 123.5 20 120.1 19 1.6 1.2 121.9 19 120.1 19 A type 63 2 0.8 121.1 18 120.1 18 2.4 0.4 120.3 18 120.1 18 3 0.8 119.1 17 118 16 3.2 0.6 118.7 17 118 16 0.8 2 157.5 19 154.1 18 1.6 1.2 155.9 19 154.1 18 80 2 0.8 155.1 18 154.1 18 2.4 0.4 154.3 18 154.1 18 3 0.8 153.1 16 152 16 3.2 0.6 152.7 16 152 16 0.8 2 197.5 18 194.1 18 1.6 1.2 195.9 18 194.1 18 100 2 0.8 195.1 18 194.1 18 2.4 0.4 194.3 18 194.1 18 3 0.8 193.1 15 192 15 3.2 0.6 192.7 15 192 15 0.8 2 247.5 18 244.1 17 1.6 1.2 245.9 17 244.1 17 1 OK 2 0.8 245.1 17 244.1 17 1 ZD 2.4 0.4 244.3 17 244.1 17 3 0.8 243.1 15 242 15 3.2 0.6 242.7 15 242 15 32 4 0.9 55.5 16 54 16 5 0.4 53.5 15 53.1 15 40 4 0.9 71.5 16 70 16 5 0.4 69.5 15 69 14 50 4 0.9 91.1 15 89.8 15 5 0.4 89.1 14 88.9 14 Btype 4 0.9 117.1 14 115.8 14 5 0.4 115.1 13 114.9 13 80 4 0.9 151.1 14 149.8 13 5 0.4 149.1 12 148.9 12 100 4 0.9 191.1 13 189.8 13 5 0.4 189.1 12 188.8 12 1 OR 4 0.9 241.1 13 239.8 13 I ZD 5 0.4 239.1 12 238.8 12 Note 1) The recommended ramping feed is 0.05mm/t. or under. 1 L (Max. Depth of Cut =151 tan a). Cutters' moving distance until depth of cut reaches APMX at a maximum ramping angle. Maximum depth of cut A type is 21mm, Btype is 20.4mm. 2 The maximum diameter when machining a blind hole with a flat face using a corner radius of 0.8mm for A type and 4mm for B type.Other than that, find with the below formula. ((cutting edge diameter DC) (corner radius) 0.3) 2 3 The minimum diameter when machining a blind hole with a flat face using a corner radius of 0.8mm for A type and 4mm for B type.Other than that, find with the below formula, (cutting edge diameter DC) (corner radius) (Width of wiper edge BS) 0.1 x2 M149 INDEXABLE MILLING