1303 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M147

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M147 1303 Lab2u

CAUTION FOR USE Procedure for attaching inserts 1) Clean the seat by air blowing or with a brush before installing the insert. 2) Tighten the clamp screw using the accessory wrench while pressing the insert against the seat. 3) Tighten the clamp screw as shown in Figure 1. 4) Coat the clamp screw with anti-seize compound and tighten it to the specified tightening torque. The tightening torque is shown below. AXD7000 3.5N,m(2.58ft,lb) AXD4000 1.5N m(1.11fMb) 5) The clamp screw is an important part in ensuring safety. Purchase an official product from Mitsubishi Materials. When using over the revolution shown in Table 2, replacing the clamp screw simultaneously with insert replacement is recommended. Type AXD4000 AXD7000 Cutting Edge Diameter DC(mm) 020 025-0125 032 040-0125 rawM Clamp Screw Number TS3SBS TS3SB TS4SB TS4SBL J1ML Overall Length L(mm) 6.5 8 9 10.5 U L- 6) Check that there is no clearance at the insert seat surface, installation of arbor type 1) Clean carefully the inside and face of the hole and the arbor face before installing the body to the arbor. 2) Set the body at the arbor and tighten it with the accessory. Refer to the table shown below for the tightening torque. 3) The set bolt supplied with the AXD is a special coolant through compatible nozzle. Be careful not to lose it. AXD4000 AXD 7 OOO Table 1 Max. Allowable Revolution AXD4000 Cutting Edge Diameter DC(mm) 025 032 040 050 063 080 0100 0125 Max. Allowable Revolution (min-i) 49000 48000 41000 35000 30000 27000 23000 20000 AXD7000 Cutting Edge Diameter DC(mm) 032 040 050 063 080 0100 0125 Max. Allowable Revolution (min-i) 41000 36000 30000 25000 23000 19000 16000 Even when operating under the maximum allowable spindle speed, if the spindle speed is equal to or higher than the values shown in table 2, it is recommended that the balance quality (with the arbor or milling chuck) conforms to G6.3 or betterbased on ISOI940. It is also recommended to replace the clamp screws with new ones when changing inserts. Furthermore.ensure to use machines that are provided with safety measures in case of cutter breakage. Note 1) The balance quality of the holder (without inserts and clamp screws) is G6.3 or better at 10,000min-1. Table 2 Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved AXD4000 Cutting Edge Diameter DC(mm) 025 032 040 050 063 080 0100 0125 Max. Allowable Revolution (min-') 12000 9500 7600 6000 4800 3800 3000 2400 AXD7000 Cutting Edge Diameter DC(mm) 032 040 050 063 080 0100 0125 Max. Allowable Revolution (min-i) 9500 7600 6000 4800 3800 3000 2400 When setting the spindle speed, take into consideration the maximum allowable spindle speed of the arbor or milling chuck. Use the specified set bolt when using the arbor type with through coolant. The inserts have sharp cutting edges and handling them with bare hands may cause injuries. Always wear safety gloves whenhandling the indexable inserts. M147 INDEXABLE MILLING