542 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.542

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 542 0542 ENG Lab2u

Hoffmann Group 47 B KOMET Parting off tool (type A, AE) 240010 - Parting-off toolholder for blades No. 240014 - 240020. The blade is clamped to the side of the slotted toolholder. Supplied without blade. 240014 - Parting off blade suitable for holder No. 240010. 240020 - Grooving blade suitable for holder No. 24 0010 for external ring grooves (Cirdip grooves): the blade width corresponds to the valid tolerance H11 for Cirdip grooves. Regrind the blade on the front face only. 240022 - Insert, required when using the grooving blade No. 240020size A0.9-A2.15 in the holder No. 240010 size A1/2A. _A1/2A A00 AO AE i A1/2A Parting-off toolholder 67.50 83.70 105.30 164.70 Overall length mm 100 125 125 170 Shank width mm 11 11 11 14.5 Shank height mm 16 18 18 22 for blade height mm 8 10 11 16 for blade width mm 2.2 2.7 0,9-2,15 4 Cutting edge height mm 12 14 14 20 suitable blade, parting-off: 240014 A00 AO - A1/2A suitable cutter, cirdip grooves: 240020 A0.9uptoA2.15 A0.9 up to A2.15 with 240022, A2.65 upto A5.15 Type A00 i AO A1/2A j Parting off blade HSS-Co5 26.34 30.92 46.58 Height h mm 8 10 16 Width b mm 2.2 2.7 4 Overall length mm 75 100 150 For tight tolerance grooves 240014 HSS Co5 240020 Width b mm A0,9 1 A1,1 A1,3 A1,6 1 A1,85 i A2.15 1 A2,65 1 A3,15 1 A4/I5 1 AS,15 1 Cirdip groove cutter H5S-Co5 62.04 62.04 62.04 62.04 62.04 62.04 (71.19) (71.19) (71.19) (80.34) for cirdip width mm 0.8 1 1.2 1.5 1.75 2 2.5 3 4 5 Overall length mm 80 80 80 80 80 80 150 150 150 150 Height h mm 11 11 11 11 11 11 16 16 16 16 suitable toolholder AEand A1/2A with Na 240022 AEand A1/2A with Na 240022 AEand A1/2A with Na 240022 AEand A1/2A with No. 240022 AEand A1/2A with Na 240022 AEand A1/2A withNa 240022 A1/2A A1/2A A1/2A A1/2A 24 0022 Adaptor for groove blade Cirdip grooving blades Grooving inserts 37.35 Q Radius turning tool 240026 - Toolholder with ground contact face and location pins for mounting radius indexable inserts. 240028/0030- Radius inserts for toolholder No. 240026. Ground all round and each with 4 radii of the same size. The cutting edges are relief ground and have chip breakers, for best cutting conditions over the entire radius sector. 240028 - Rake angle 5° suitable for cast iron, brass, bronze. 240030 - Rake angle 12° suitable for steel, cast steel, stainless steel and light metal alloys. Application: For turning convex radii on external or internal diameters. 240026 Outer radius 7 Shank cross section mm 10 1 12 i 16 20 1 25 TooMdersfor radius indexable inserts 87.52 87.52 78.41 96.23 120.29 for radius indexable inserts R1-R6 R1-R6 R1-R6 R1-R6 R8-12 Shank height mm 10 12 16 20 25 Shank width mm 10 12 16 20 25 Shank length mm 103 103 103 117 125 Radius 24 0028 24 0030 542 Radius indexable insert 5° HSS-Co5,H7 Radius indexable insert 12° HSS-Co5,H7 HSS Co5 VH R1,5 SI R2,5 R5 I R6 IKiMI R10 I R12 130.19 130.19 - 130.19 130.19 130.19 130.19 130.19 130.19 130.19 130.19 130.19 130.19 130.19 130.19 165.33 165.33 165.33 EOALCO nlii im4 -fc1 PATtNTCO 24 0028_R3 24 0030_R3