422 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.422

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 422 0422 ENG Lab2u

Hoffmann Group 47 MTC 4aBM id Plunge milling cutters 90° and 93° MTC for VCG. 2205.. Greater tool stiffness by elimination of twist between indexable insert and insert seat. Plunge milling cutter 90° for VCG. 2205.. Form fit 0D/number of teeth Z mm i 211811 0D, h6 mm K, mm 0D2 mm Mounting thread M suitable indexable insert Pack of insert screws Plunge milling cutter 90° with threaded shank 32/2 257.40 17 47 29 M16 VCG.2205 219800 (20IP; 5.7 Nm) 40/3 303.93 17 47 29 M16 VCG.2205 219800 (20IP; 5.7 Nm) 42/3 303.93 17 47 29 M16 VCG.2205 219800 (20IP; 5.7 Nm) 0D/number of teeth Z mm 1 211806 L mm Mounting bore 0 mm suitable indexable insert Pack of insert screws Plunge milling cutter 90° with bore 40/3 297.99 55 16 VCG.2205 219800 (20IP; 5.7 Nm) 42/3 297.99 55 16 VCG.2205 219800 (20IP; 5.7 Nm) 50/4 355.41 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 52/3 330.66 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 63/4 365.31 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 66/4 365.31 55 27 VCG.2205 219800 (20IP; 5.7 Nm) 80/5 404.91 55 27 VCG.2205 219800 (20IP; 5.7 Nm) Plunge milling cutter 93° for VCG. 2205., 93° Application: To prevent chips jamming, especially when milling deep pockets. 0D/ number of teeth Z 211813 0D, h6 L, 0D2 Mounting thread M suitable indexable insert Pack of insert screws Plunge milling cutter 93° mm with threaded shank mm 32/2 257.40 17 47 29 Ml 6 VCG.2205 219800 (20IP; 5.7 Nm) 40/3 303.93 17 47 29 M16 VCG.2205 219800 (20IP; 5.7 Nm) 42/3 303.93 17 47 29 M16 VCG.2205 219800 (20IP; 5.7 Nm) 0D/number of teeth Z Lmi'iM I, ot Aufnahmebohrungs- 0 suitable indexable insert Pack of insert screws Plunge milling cutter 93° mm with bore mm 40/3 297.99 55 16 VCG.2205 219800 (20IP; 5.7 Nm) 42/3 297.99 55 16 VCG.2205 219800 (20IP; 5.7 Nm) 50/4 355.41 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 52/3 330.66 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 63/4 365.31 55 22 VCG.2205 219800 (20IP; 5.7 Nm) 66/4 365.31 55 27 VCG.2205 219800 (20IP; 5.7 Nm) 80/5 404.91 55 27 VCG.2205 219800 (20IP; 5.7 Nm) Milling inserts for plunge milling cutters No. 211806 - 211813 21 1853-1859 - Fine-grain substrate, polished chip breaker steps - extreme reduction in the tendency to edge build-up. 211860 - Diamond-coated milling insert for higher cutting speeds and longer tool life in materials with silicon content. Note: = 15 mm for roughing with ae = 1 xD. Suitable for/ v( m/min Alu plastics c&£L, Alu cast >10% SI X < 500 N X < 750 N X <900N X < 1100 N X < 1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900N INOX >900N Ti > B50N CuZn Graphite GRP CRP 6 6 ISO code N N hr P H N N 211853-211859 1900 1900 500 400 100 O 211860 1900 1900 680 o Type ALU O VCGX 220505 FR HU7810 18.54 10 = 211856 VCGX 220508 FR HU7810 18.54 10 S211857 VCGX 220516 FR HU7810 18.54 10 £211859 VCGX 220520 FR HU7810 18.54 10 £211858 VCGT 220530 FN HU7810 18.54 10 211860 VCGT220530FN diamond-coated HB7810 51.08 1 f, mm 0.25 211853 saf Set w 211859 21 1860 422 15 mm 15 mm