Пластины Mitsubishi из сверхтвердых режущих материалов КНБ и ПКА CBN & PCD TURNING INSERTS

Пластины Mitsubishi из сверхтвердых режущих материалов КНБ и ПКА CBN & PCD TURNING INSERTS

Пластины Mitsubishi из сверхтвердых режущих материалов КНБ и ПКА CBN & PCD TURNING INSERTS _CBN > Suitable for high speed finishing of heat treated steel, sintered ferrous alloy and cast iron. I Low affinity to iron, thus good surface finishes are possible. I Grinding can be replaced by machining. I Heat Treated Steel Обрабатываемые материалы Work Material Type Cutting Mode Recommended Grade Recommended Cutting Conditions Скорость резания (м/мин) Cutting Speed (m/min) Подача (мм/оборот) Feed (mm/rev) Глубина резания (мм) Depth of Cut (mm) Structural Steel Esp. Carburized Steel (SC, SCM, SCr) High Alloy Steel (SKD, SKH) HRC 35-65 Coated High speed finishing cutting BC8105 250(100-350) -0.15 -0.2 MBC010 250(150-400) -0.2 -0.2 Continuous cutting for general purpose BC8110 200 (100-300) -0.2 -0.3 MBC020 200 (80-250) -0.2 -0.3 Heavy interrupted cutting for general purpose < BC8120 200 (80-250) -0.3 -0.8 interrupted cutting for general purpose BC8020 150 (60-200) -0.2 -0.3 Interrupted cutting BC8130 120 (60-150) -0.2 -0.3 Non-coated Continuous cutting for general purpose MB8025 180 (80-250) -0.3 -5 Interrupted cutting for general purpose 120 (60-150) -0.2 -0.3 High speed finisning cutting MB810 200(150-300) -0.3 -0.15 Continuous to lijght interrupted cutting MB825 120 (70-150) -0.3 -0.5 Interrupted cutting MB83S 100 (50-120) -0.3 -0.5 Cast Iron Обрабатываемые материалы Work Material Workpiece Structure Скорость резания (м/мин) Cutting Speed (m/min) Подача (мм/оборот) Feed (mm/rev) Глубина резания (мм) Depth of Cut (mm) Coolant 250 500 750 1000 1250 Gray Cast Iron JIS FC250 Ferritic + Pearlitic MBS 140 1 -0.5 -1.0 MBS140 -5.0 Dry,Wet JIS FC300 Pearlitic MB710 MB730\ Alloy Cast Iron Pearlitic 11 MB4aen i -0.4 -0.5 Dry,Wet Ductile Cast Iron JIS FCD400 Ferritic I MB71D -0.4 -0.5 Dry,Wet JIS FCD700 Ferritic + Pearlitic Pearlitic MB730 Sintered Alloy Обрабатываемые материалы Work Material Recommended Grade Recommended Cutting Conditions Скорость резания (м/мин) Cutting Speed (m/min) Подача (мм/оборот) Feed (mm/rev) Глубина резания (мм) Depth of Cut (mm) General Sintered Alloy MB4020 250 (80-300) -0.2 -0.3 High Density Sintered Alloy MB4020 150 (80-250) -0.2 -0.3 Sintered Alloy MB4020, MB835 100(80-150) -0.2 -0.3 (Valve Seat Amount of Hard Particles None or Small Large Hardness of Workpiece (HV) 150 250 300 350 Plunge Cut mihti.hj.i fl MBBB5 MBB3S Traverse Cut Ml MBBS5 l Roll Обрабатываемые материалы Work Material Grade Recommended Cutting Conditions Скорость резания (м/мин) Cutting Speed (m/min) Подача (мм/оборот) Feed (mm/rev) Глубина резания (мм) Depth of Cut (mm) Cast Steel Adamite Cast Steel MB825, MB8025 80(30-130) 0.3 (0.1-0.5) 0.2 3.0 Ductile Cast Iron Granular Cast Iron Chilled Cast Iron MB710 80 (30-130) 0.3 (0.1-0.5) 0.2 3.0 High Chromium Steel Hgh Alloy Steel MB825, MB8025 80 (30-130) 0.3 (0.1-0.5) 0 CO 1 CN d High Speed Steel MB730 50 (20-70) 0.25(0.1-0.4) 0.1-3.0 Cemented Carbide MB730, MBS140 20 (10-30) -0.2 -0.2 >Heat Resistant Alloy Обрабатываемые материалы Work Material Grade Recommended Cutting Conditions Скорость резания (м/мин) Cutting Speed (m/min) Подача (мм/оборот) Feed (mm/rev) Глубина резания (мм) Depth of Cut (mm) Ni Base Heat Resistant Alloy (e.g. Inconel) MB730, MB8025 120(100-150) -0.2 -0.5 Co Base Heat Resistant Alloy (e.g. Stellite) MB730, MB8025 70 (50-100) -0.2 -0.5 Mitsubishi Materials 209 CBN & PCD TURNING INSERTS