2338 Каталог WALTER 2012 Металлорежущий инструмент и оснастка Valenite для станков Стр.F410

Каталог WALTER 2012 Инструмент и оснастка Valenite Стр. F410 2338 ENG Lab2u

WALTER Valenite Technical information Milling Feed determination (starting values) Copy mill Material group Mill type =fl F 2139 1 Feed per tooth fzo for ae Dc ap ap max Lc D ( c Lc 1 r i Approach angle k Page F 314 Tool 0 or 0 range in fZ0 in 8 mm 10 mm 12 mm 16 mm Maximum cutting data ap max Lc in 0.157 0.197 0.236 0.315 p Unalloyed steel 1 0.003 0.004 0.004 0.005 Low-alloyed steel 0.002 0.003 0.003 0.004 High-alloyed steel and tool steel 0.002 0.003 0.003 0.004 Stainless steel 0.002 0.002 0.002 0.003 M Stainless steel 2 0.002 0.002 0.002 0.003 K Malleable cast iron 0.003 0.004 0.004 0.005 Grey cast iron 0.004 0.005 0.005 0.006 Cast iron with spheroidal graphite 0.003 0.004 0.004 0.005 GGV (CGI) 0.003 0.004 0.004 0.005 N Aluminum wrought alloys 0.002 0.003 0.003 0.004 Cast aluminum alloys 0.002 0.003 0.003 0.004 Magnesium alloys 0.002 0.003 0.003 0.004 Copper and copper alloys (bronze / brass) 0.002 0.002 0.002 0.003 S Heat-resistant alloys 0.002 0.002 0.002 0.002 Titanium alloys 0.002 0.002 0.002 0.002 Tungsten alloys 0.002 0.002 0.002 0.002 Molybdenum alloys 0.002 0.002 0.002 0.002 H Hardened steel 0.002 0.002 0.002 0.002 Hardened cast iron 0.002 0.002 0.002 0.003 O Thermoplasts 0.003 0.004 0.005 0.005 Plastic, carbon-fiber reinforced Graphite (technical) 0.003 0.004 0.005 0.005 Insert types P32 -D08 P32 -D10 P32 -D12 P32 -D16 Correction factor Kae ae / Dc for the feed per tooth depending on the ratio of cut width ae to cutter diameter Dc 1/1 1/2 1.0 1.0 1.0 1.0 1/5 1.2 1.2 1.2 1.2 1/10 1.5 1.5 1.5 1.5 1/20 1.8 1.8 1.8 1.8 1/50 2.0 2.0 2.0 2.0 Correction factor Kap ap for the feed per tooth depending on the cutting depth ap fz fzo Kae Kap 0.2 1.8 2.3 2.3 2.5 0.4 1.5 2.0 2.0 2.2 0.6 1.2 1.7 1.7 1.9 0.8 1.0 1.3 1.3 1.5 1.0 0.8 1.0 1.0 1.2 1.5 0.7 0.8 0.8 1.0 2.0 0.6 0.7 0.7 0.8 3.0 0.5 0.6 0.6 0.7 4.0 0.5 0.5 0.5 0.6 ap max Lc 0.5 0.5 0.5 0.5 1 and cast steel 2 and austenitic / ferritic 3 Correction factor Kae Kap do not set to more than 3 when finishing F 410