333 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.329

Каталог TUNGALOY 2007 Режущий инструмент Стр. 329 0333 ENG Lab2u

TRD12M6 Copy milling Complex curvature for Copy mills 0d Rake angle A.R. +10" R.R. -6 0 TRD12 - Max. cutting depth 6 mm TRD16 - Max. cutting depth 8 mm Cat. No. Stock Inserts No. of inserts Dimensions (mm) 0D 0Di 0d Weight (kg) Mounting details TRD12050R-E 4 38 50 20 6.3 10.4 0.2 TRD12052R-E RDMT1204ZDPN-MJ 4 40 52 40 20 22 6.3 10.4 0.3 P 339 TRD12063R-E RDMW1204ZDSN 5 6 51 63 20 6.3 10.4 0.4 TRD12066R-E 5 54 66 22 7 12.4 0.8 TRD12080R-E 6 68 80 50 22 27 7 12.4 0.4 P 339 TRD12100R-E 6 88 100 26 32 8 14.4 0.7 TRD16063R-E 4 47 63 40 20 22 6.3 10.4 1.1 P 339 TRD16066R-E RDMT1606ZDPN-MJ 4 8 50 66 22 27 7 12.4 2.4 TRD16080R-E RDMW1606ZDSN 5 64 80 50 22 7 12.4 TRD16100R-E 6 84 100 26 32 8 14.4 P 339 R b Inserts 4-R 4-R Grades Dimensions (mm) Cat. No. Accuracy Honing Figure PVD Coated CVD Coated AH120 AH140 AH330 T3030 A S bs R RDMT1204ZDPN-MJ 1 12.8 4.76 6 RDMW1204ZDSN M With 2 0.8 RDMT1606ZDPN-MJ 1 16.8 6.35 8 RDMW1606ZDSN 2 Standard cutting conditions Replacement parts Work material Insert grade Cutting speed Vc (m/min) Feed per tooth ft (mm t) TRD12 TRD16 Carbon steels 300 HB T3030 AH120 AH330 190 (140 240) 170 (120 220) 190 (140 240) 0.3 0.5 0.3 0.5 0.2 0.4 0.3 0.6 0.3 0.6 0.2 0.5 Alloy steels 300 HB T3030 AH120 AH330 170 (120 220) 150 (100 200) 170 (120 220) 0.2 0.45 0.2 0.45 0.15 0.35 0.2 0.5 0.2 0.5 0.15 0.4 Die steels 300 HB T3030 AH120 AH330 150 (100 200) 130 (80 180) 150 (100 200) 0.2 0.35 0.2 0.35 0.1 0.3 0.25 0.45 0.25 0.45 0.1 0.4 Cast irons AH120 AH330 180 (120 240) 200 (150 250) 0.3 0.5 0.2 0.4 0.3 0.6 0.2 0.5 Hardened steels prehardened steels 45 HRC AH120 100 (60 140) 0.08 0.25 0.1 0.3 Stainless steel AH140 150 (80 200) 0.2 0.5 0.2 0.6 Description Parts Cat. No. TRD12 TRD16 Clamping screw Wrench CSTB-3.5 T-15D CSTB-5 T-20D No. of revolutions n (rpm) Cutting speed Vc (m/min) x 1000 3.14 Cutter 0 (mm) Table feed Vf (mm/min) n (rpm) x Feed per tooth ft (mm t) x t (No. of inserts) Note When the cutting depth is smaller than 2 mm use the higher limit of feed values shown above. And when larger than 3 mm use the lower limit of the feed values. Features Reference Technical data P. 298 302 guide P. 476 479 TAC Mills