332 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.328

Каталог TUNGALOY 2007 Режущий инструмент Стр. 328 0332 ENG Lab2u

TAC Mills TRF6000 For high-speed and high-feed milling of super alloys and stainless steels (Irregular pitch design) Rake angle A.R. +19" R.R. +3" Max. cutting depth 3 mm Right hand (R) shown Cat. No. Stock No. of inserts Dimensions mm) Weight (kg) Mounting details R/L 0D 0D1 0d E F a b TRF6003R/LIE 4 80 100 27 26 50 7 12.4 1.4 TRF6004R/LIE 5 100 120 32 32 63 8 14.4 2.5 P 339 TRF6005R/LIE 6 125 145 40 32 63 9 16.4 3.9 TRF6006R/LIE 8 160 180 40 29 63 9 16.4 5.8 TRF6008R/LIE 10 200 220 60 38 63 14 25.7 9.8 P 339 TRF6010R/LIE 12 250 270 60 38 63 14 25.7 17.3 TRF6012R/LIE 14 315 335 60 38 63 14 25.7 27.8 P 339 Inserts RFEN2004ZFTN (With partially flattened flanks) ISN 25" RFEN2004M0TN Fig. 1 4.76 Fig. 2 25" t 4.76 Cat. No. Type Accuracy Honing Grades Figure PVD Coated Uncoated AH120 KS20 UX30 RFEN2004ZFTN With flats E With 1 RFEN2004M0TN Without flats E With 2 Note RFEN2004M0TN type inserts should not be used for finishing requiring surface finish better than 12S. RFEN2004ZFTN type inserts can be used for both finishing and roughing at cutting depth up to 3 mm. Replacement parts Standard cutting conditions No. Description Parts Cat. No. TRF6003R/LI TRF6006R/LI TRF6008R/LI TRF6012R/LI 1 Locator Insert locking wedge Wedge fixing screw Locator fixing screw T-handle wrench LF602R/L WF603R/L FDS-8S CM4X0.7X20 TP-4 LF602R/L WF608R/L FDS-8S CM4X0.7X20 TP-4 Insert grades Cutting depth ap 1 3 mm Cutting depth ap 0.4 1 mm materials Cutting speed Vc (m/min) Feed per tooth ft (mm t) Cutting speed Vc (m/min) Feed per tooth ft (mm t) Cutting fluid Super alloys (Inconel etc) AH120 20 40 0.1 0.15 20 60 0.2 0.4 Water insoluble type Titanium alloys (Ti-6AI-4V etc) AH120 40 60 0.15 0.35 40 70 0.2 0.5 Water soluble type or dry cutting Stainless steels Austenitic Ferritic ( HB300) UX30 150 230 0.2 0.35 180 250 0.2 0.5 Dry cutting Precipitation hardening ( HRC35) UX30 130 180 0.15 0.3 150 200 0.2 0.4 Dry cutting Hard materials (HRC40-55) AH120 20 50 0.05 0.1 20 50 0.05 0.2 Water insoluble type 1 No. of revolutions n (rpm) Cutting speed Vc (m/min) x 1000 1 Table feed Vf (mm/min) n (rpm) x Feed per tooth ft (mm t) x Note Cutting width should be within 60 to 70 of effective cutter diameter. 3.14 Cutter 0 (mm) t (No. of inserts) Features Reference Technical data P. 298 302 guide P. 476 479