326 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.322

Каталог TUNGALOY 2007 Режущий инструмент Стр. 322 0326 ENG Lab2u

TAC Mills TPP16 Highly reliable square shoulder mills Cat. No. Stock No. of inserts Dimensions (mm) Weight (kg) Mounting details 0D 0d E F a b TPP16080RIE 4 80 27 26 50 7 12.4 1.0 TPP16100RIE 5 100 32 32 63 8 14.4 1.8 P. 339 TPP16125RIE 6 125 40 32 63 9 16.4 2.8 TPP16160RIE 8 160 40 29 63 9 16.4 4.6 TPP16200RIE 10 200 60 38 63 14 25.7 6.9 P. 339 TPP16250RIE 12 250 60 38 63 14 25.7 13.0 TPP16315RIE 14 315 60 38 63 14 25.7 22.2 P. 339 Inserts Replacement parts SPMR1605PPPR-ML SPMR1605PPTR-MJ SPMR1605PPTR-MH Cat. No. Accuracy Honing Grades PVD Coated CVD Coated Uncoated GH330 GH340 T3030 T1015 UX30 SPMR1605PPPR-ML M with SPMR1605PPTR-MJ SPMR1605PPTR-MH Standard cutting conditions For ML-chipbreaker inserts (Sharpness-priority) Work materials Insert grades Roughing Finishing Cutting speed Vc (m/min) Feed per tooth ft (mm t) Cutting speed Vc (m/min) Feed per tooth ft (mm t) Mild steels ( 180 HB) GH340 GH330 AH330 100 200 130 230 130 370 0.05 0.17 0.05 0.17 0.05 0.17 100 230 150 250 150 400 0.05 0.20 0.05 0.20 0.05 0.20 Stainless steels ( 250 HB) GH340 GH330 100 170 150 200 0.05 0.12 0.05 0.12 100 200 200 250 0.05 0.15 0.05 0.15 Carbon steels Alloy steels ( 250 HB) GH340 GH330 AH330 100 170 100 180 100 300 0.05 0.12 0.05 0.12 0.05 0.12 100 200 150 200 150 320 0.05 0.15 0.05 0.15 0.05 0.15 No. Description Parts Cat. No. Locator LPP16R/L Insert locking wedge WPP16R/L Wedge fixing screw FDS-8S(FDS-8SS) Locator fixing screw CM5X0.8X12 T-handle wrench TP-4 For MJ-chipbreaker inserts (General purpose) Work materials Insert grades Roughing (Cutting depth ap 1.5 mm) Finishing (Cutting depth ap 0.3 0.7 mm) Vc (m/min) ft (mm t) Vc (m/min) ft (mm t) Mild steels ( 180 HB) GH330 T3030 UX30 100 230 130 230 100 180 0.10 0.25 0.10 0.28 0.10 0.25 130 250 180 300 130 200 0.10 0.30 0.10 0.30 0.10 0.30 Carbon steels Alloy steels ( 300 HB) GH330 T3030 UX30 100 180 130 180 80 130 0.10 0.20 0.10 0.25 0.10 0.20 130 200 180 280 100 150 0.10 0.28 0.10 0.28 0.10 0.28 Die steels ( 30 HRC) GH330 T3030 UX30 100 150 100 150 80 130 0.10 0.18 0.10 0.18 0.10 0.18 100 150 100 150 80 130 0.10 0.20 0.10 0.20 0.10 0.20 Cast irons Ductile cast irons T1015 UX30 100 200 80 130 0.10 0.20 0.10 0.20 100 200 80 130 0.10 0.25 0.10 0.25 Stainless steels ( 250 HB) GH330 T3030 150 200 150 200 0.15 0.23 0.15 0.23 200 250 200 250 0.15 0.25 0.15 0.25 No. of revolutions n (rpm) Cutting speed Vc (m/min) x 1000 r 3.14 r Cutter 0 (mm) Table feed Vf (mm/min) n (rpm) x Feed per tooth ft (mm t) x t (No. of inserts) Features Reference Technical data P 90S 302 guide P 476 47Q S For MH-chipbreaker inserts (Toughness-priority) Work materials Insert grades Roughing (Cutting depth ap 1.5 mm) Finishing (Cutting depth ap 0.3 0.7 mm) Vc (m/min) ft (mm t) Vc (m/min) ft (mm t) Mild steels ( 180 HB) GH330 T3030 UX30 100 230 130 230 100 180 0.15 0.30 0.15 0.33 0.15 0.30 130 250 180 300 130 200 0.15 0.35 0.15 0.38 0.15 0.35 Carbon steels Alloy steels ( 300 HB) GH330 T3030 UX30 100 180 130 180 80 130 0.15 0.24 0.15 0.30 0.15 0.24 130 200 180 280 100 150 0.15 0.35 0.15 0.35 0.15 0.35 Die steels ( 30 HRC) GH330 T3030 UX30 100 150 100 150 80 130 0.15 0.22 0.15 0.22 0.15 0.22 100 150 100 150 80 130 0.15 0.28 0.15 0.28 0.15 0.28 Cast irons Ductile cast irons T1015 UX30 100 200 80 130 0.15 0.24 0.15 0.24 100 200 80 130 0.15 0.30 0.15 0.30 Notes As a rule dry cutting (including air-blowing) is generally recommended. If a cutting fluid is used the cutting speed should be set to the lower side of the values shown in the above table. When being used in square shoulder milling climb milling is recommended. In square shoulder milling of stainless steel when chips tend to be recut during cutting change to up-milling mode.