1069 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.K037

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. K037 1069 Lab2u

iMX-C4HV Corner radius head, 4 flute, Irregular helix, Long cutting edge type RECOMMENDED CUTTING CONDITIONS Shoulder milling (mm) Work Material Carbon steel, Alloy steel, Mild steel, Copper, Copper alloys AISI 1045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloy AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V L/D Dia. DC Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae 4 16 100 2000 0.09 720 32 0.8 80 1600 0.07 450 32 0.8 60 1200 0.08 380 32 0.8 20 100 1600 0.09 580 40 1 80 1300 0.07 360 40 1 60 950 0.08 300 40 1 6 16 60 1200 0.07 340 32 0.8 50 990 0.05 200 32 0.8 40 800 0.06 190 32 0.8 20 60 950 0.07 270 40 1 50 800 0.05 160 40 1 40 640 0.06 150 40 1 LU OL D o CO m Depth of cut fae O' LU a. x o 0 z 1 o 3 o cx Work Material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Heat resistant alloys lnconel718 L/D Dia. DC Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae 4 16 50 990 0.07 280 32 0.8 30 600 0.05 120 32 0.4 20 50 800 0.07 220 40 1 30 480 0.05 96 40 0.5 6 16 30 600 0.05 120 32 0.8 20 400 0.04 64 32 0.4 20 30 480 0.05 96 40 1 20 320 0.04 51 40 0.5 Depth of cut Note 1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Note 4) The length of the long cutting type is 2 times that of the standard head. L/D demonstrates +1 when installed to a holder of the same size. a m K037