959 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J337

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J337 0959 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Work Material Graphite Copper, Copper alloys Dia. DC (mm) Corner radius RE (mm) Neck length LU (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) 0.5 0.1 4 30000 1100 0.05 0.23 24000 700 0.04 0.23 0.1 5 28000 960 0.05 0.23 22000 600 0.04 0.23 0.1 6 25000 850 0.05 0.23 20000 540 0.04 0.23 0.1 10 22000 600 0.04 0.21 0.1 15 20000 500 0.03 0.18 0.8 0.1 6 28000 1300 0.08 0.45 22000 830 0.06 0.45 0.1 8 22000 900 0.08 0.45 18000 580 0.06 0.45 1 0.1 8 25000 1500 0.1 0.6 20000 960 0.08 0.6 0.1 12 22000 1300 0.1 0.6 18000 830 0.08 0.6 0.2 8 25000 1500 0.1 0.45 20000 960 0.08 0.45 0.2 12 22000 1300 0.1 0.45 18000 830 0.08 0.45 0.2 16 18000 1000 0.08 0.4 14000 640 0.06 0.4 0.2 20 15000 800 0.08 0.4 0.2 30 12000 600 0.07 0.35 1.5 0.2 10 18000 1400 0.15 0.8 14000 900 0.12 0.8 0.2 20 12000 900 0.12 0.65 9600 580 0.1 0.65 2 0.1 8 24000 3300 0.2 1.2 19000 2100 0.16 1.2 0.2 12 22000 3000 0.2 1.2 18000 1900 0.16 1.2 0.2 16 19000 2500 0.2 1.2 15000 1600 0.16 1.2 0.2 20 16000 2000 0.2 1.2 13000 1300 0.16 1.2 0.2 30 13000 1600 0.16 1.0 0.2 40 11000 1200 0.14 0.8 0.3 8 24000 3300 0.3 1.2 19000 2100 0.24 1.2 3 0.2 20 18000 3000 0.3 2.0 14000 1900 0.24 2.0 0.2 40 12000 1800 0.25 1.7 9600 1100 0.2 1.7 0.5 20 18000 3000 0.3 1.5 14000 1900 0.24 1.5 0.3 12 20000 4500 0.3 1.5 16000 2900 0.24 1.5 4 0.2 20 18000 4200 0.4 2.7 14000 2700 0.3 2.7 0.2 40 13000 2800 0.4 2.7 10000 1800 0.3 2.7 0.5 20 18000 4200 0.4 2.3 14000 2700 0.3 2.3 0.5 40 13000 2800 0.4 2.3 10000 1800 0.3 2.3 6 0.1 24 14000 4600 0.6 3.8 11000 2900 0.5 3.8 0.3 24 14000 4600 0.6 3.8 11000 2900 0.5 3.8 0.5 24 14000 4600 0.6 3.8 11000 2900 0.5 3.8 0.5 30 14000 4600 0.6 3.8 11000 2900 0.5 3.8 1 30 14000 4600 0.6 3.0 11000 2900 0.5 3.0 8 0.5 30 10500 4000 0.8 5.3 8400 2600 0.6 5.3 1 30 10500 4000 0.8 4.5 8400 2600 0.6 4.5 10 0.5 40 8700 3500 1.0 6.8 7000 2200 0.8 6.8 1 40 8700 3500 1.0 6.0 7000 2200 0.8 6.0 12 0.5 40 7200 3000 1.2 8.0 5800 1900 1.0 8.0 ae Note 1) When high machining accuracy is needed, or the workpiece becomes chipped, we recommend lowering the feed rate. Note 2) Use a milling machine dedicated for graphite. Note 3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. J337 ROUGHING BARREL TAPER rlilrillfcM BALL SQUARE