683 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J061

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J061 0683 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Work Material Depth of cut Carbon steel, Cast iron, Alloy steel, Pre-hardened steel AIS11050, AISI No 35 B, AISI P20, AISI P21 Dia. DC (mm) Neck length LU (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) 0.2 0.5 40000 600 0.004 1 40000 400 0.001 0.3 1 40000 650 0.007 3 40000 500 0.002 9 22000 150 0.001 0.4 2 40000 800 0.007 4 40000 800 0.003 12 17000 150 0.001 0.5 2 40000 950 0.01 6 40000 700 0.003 10 25000 400 0.002 15 14000 150 0.001 0.6 2 40000 950 0.01 6 40000 800 0.005 10 25000 450 0.003 18 12000 150 0.001 0.7 2 40000 1000 0.02 6 40000 900 0.01 8 30000 700 0.005 10 11000 300 0.005 0.8 4 40000 1200 0.02 8 40000 1000 0.01 12 25000 400 0.003 24 10000 150 0.001 0.9 6 40000 1300 0.02 10 35000 1000 0.01 15 9000 400 0.003 1 6 40000 1600 0.04 8 40000 1600 0.03 12 30000 1000 0.02 20 15000 400 0.005 30 8000 150 0.001 1.2 6 40000 1900 0.06 8 40000 1900 0.04 12 25000 1000 0.03 20 6500 150 0.01 DC 0 ap DC:Dia. Work Material Depth of cut Carbon steel, Cast iron, Alloy steel, Pre-hardened steel AIS11050, AISI No 35 B, AISI P20, AISI P21 Dia. DC (mm) Neck length LU (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) 1.5 6 40000 2400 0.10 10 30000 1800 0.05 20 15000 600 0.02 30 7500 300 0.005 45 5000 150 0.001 1.6 6 40000 2400 0.12 10 30000 1800 0.07 16 20000 1000 0.04 2 6 40000 2400 0.18 10 30000 1800 0.10 16 20000 1000 0.06 30 8000 500 0.04 40 6000 250 0.01 60 4200 150 0.003 2.5 8 25000 2500 0.20 16 18000 1700 0.10 20 12000 1000 0.08 40 8000 400 0.03 50 4000 150 0.015 3 8 20000 2000 0.30 16 15000 1400 0.15 20 10000 800 0.10 40 5000 250 0.02 50 3700 150 0.010 4 12 15000 3000 0.30 20 11000 2200 0.22 30 6400 1200 0.12 40 4500 400 0.05 50 2800 150 0.018 60 1800 60 0.005 5 16 12000 2500 0.35 35 5100 750 0.15 60 2200 150 0.02 6 20 10000 2000 0.40 40 4200 800 0.20 60 1900 150 0.10 DC: Dia. Note 1) If the depth of cut is shallow, the revolution and feed rate can be increased. Note 2) Cutting condition may be considerably different due to the overhang (milling depth), depth of cut, and machine tools. Please see the above table as a standard. o in J061 ROUGHING BARREL TAPER RADIUS BALL