Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING _ AHXE405 Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Dry Cutting (mm) Обрабатываемые материалы Work Material Hardness Grade Breaker VC (m/min) fz (mm/t.) ap ae P MP6120 M 250(200-300) 0.3 (0.2 0.4) <5 <0.8DC Mild Steel 180HB VP15TF MP 250(200-300) 0.3 (0.2 0.4) 5 0.8DC MP6130 M 220(170-270) 0.4 (0.3 0.5) i5 i0.8DC MP6120 M 220(170-270) 0.3 (0.2 0.4) 5 i0.8DC Carbon Steel,Alloy Steel 180-280HB VP15TF MP 220(170-270) 0.3 (0.2 0.4) <5 <0.8DC MP6130 M 190(140-240) 0.4 (0.3 0.5) <5 <0.8DC MP6120 M 140(100-180) 0.3 (0.2-0.4) <5 <0.8DC Carbon Steel,Alloy Steel 280 350HB VP15TF MP 140(100-180) 0.3 (0.2 0.4) <5 <0.8DC MP6130 M 110(70-150) 0.4 (0.3 0.5) <5 <0.8DC MP6120 M 140(100-180) 0.15(0.1-0.2) <3 <0.8DC Pre-hardened Steel <350HB (annealing) VP15TF MP 140(100-180) 0.15(0.1-0.2) <3 <0.8DC MP6130 M 110(70-150) 0.25(0.2-0.3) <3 <0.8DC MP6120 M 140(100-180) 0.15(0.1-0.2) <3 <0.8DC Alloy Tool Steel 35-45HRC VP15TF MP 140(100-180) 0.15(0.1-0.2) <5 <0.8DC MP6130 M 110(70-150) 0.25(0.2-0.3) <3 <0.8DC M Austenitic Stainless Steel <200HB MP7030 MM 200(150-250) 0.2 (0.1-0.3) <5 <0.8DC Austenitic Stainless Steel > 200HB MP7030 MM 150(100-200) 0.2 (0.1-0.3) <5 <0.8DC Two-phase Stainless Steel <280HB MP7030 MM 140(100-180) 0.15(0.05-0.25) <5 <0.8DC Ferritic and Maltensitlc Stainless Steel <200HB MP7030 MM 200(150-250) 0.2 (0.1-0.3) <5 <0.8DC Ferritic and Maltensitlc Stainless Steel > 200HB MP7030 MM 150(100-200) 0.2 (0.1-0.3) 5 0.8DC Precipitation Hardening Stainless Steel < 450HB MP7030 MM 130(100-160) 0.15(0.05-0.25) <5 <0.8DC K MC5020 MK,HK 220(150-300) 0.3 (0.2 0.4) <5 <0.8DC Gray Cast Iron Tensile Strength <350MPa VP15TF, VP20RT MK,HK 180(130-230) 0.3 (0.2 0.4) <5 <0.8DC VP15TF MP 180(130-230) 0.3 (0.2 0.4) <5 <0.8DC MC5020 MK,HK 200(150-250) 0.2 (0.1-0.3) <5 <0.8DC Ductile Cast Non Tensile Strength 450MPa VP15TF,VP20RT MK,HK 170(120-220) 0.2 (0.1-0.3) <5 <0.8DC VP15TF MP 170(120-220) 0.2 (0.1-0.3) <5 <0.8DC MC5020 MK,HK 170(150-200) 0.2 (0.1-0.3) <5 <0.8DC Ductile Cast Non Tensile Strength <800MPa VP15TF.VP20RT MK,HK 140(100-180) 0.2 (0.1-0.3) <5 <0.8DC VP15TF MP 140(100-180) 0.2 (0.1-0.3) <5 <0.8DC H Hardened Steel 40-55HRC VP15TF MP 80(60-100) 0.15(0.1-0.2) <3 <0.8DC (Notel) Recommended wet cutting for good surface finishing of stainless steel. (Tool life is short compared to wet cutting.) (Note2) We recommend wet cutting with internal coolant for titanium alloy and heat resistant alloy. (Note3) When clamp rigidity is low and tool overhang is long, we recommended to reduce the cutting speed and the feed rate by 30%. 1394 Mitsubishi Materials