110 Каталог KYOCERA 2016 Фрезы со сменными режущими пластинами для металлообработки Стр.E26

Каталог KYOCERA 2016 Инструмент фрезерный с СРП по металлу Стр. E26 0110 ENG Lab2u

90° LEAD MECX Recommended Cutting Conditions Workpiece Material Feed Rate fz (ipt) Recommended Insert Grade Vc (sfm) JS Chipbreaker JT Chipbreaker MEGACOAT NANO MEGACOAT PVD Coated Carbide CVD Coated Carbide PR1535 PR1225 PR1210 PR830 CA6535 Carbon Steel 0.0016 0.0031 0.0039 0.0024 0.0039 0.0047 390 590 820 390 590 820 390 490 590 - Alloy Steel 0.0016 0.0024 0.0031 0.0024 0.0031 0.0039 330 520 720 330 520 720 330 460 590 - Mold Steel 0.0016 0.0024 0.0031 0.0024 0.0031 0.0039 260 460 590 260 460 590 260 390 490 - Austenitic Stainless Steel 0.0012 0.0016 0.0020 0.0020 0.0024 0.0028 330 520 660 330 520 660 Martensitic Stainless Steel 0.0012 0.0016 0.0020 0.0020 0.0024 0.0039 490 660 820 - 590 790 980 Precipitation Hardened Stainless Steel 0.0012 0.0016 0.0020 0.0020 0.0024 0.0039 300 390 490 Gray Cast Iron 0.0016 0.0031 0.0039 0.0031 0.0039 0.0059 390 590 820 Nodular Cast Iron 0.0016 0.0024 0.0031 0.0031 0.0039 0.0047 330 490 660 Ni-base Heat Resistant Alloy 0.0012 0.0016 0.0020 0.0020 0.0024 0.0028 70 100 160 - 70 100 160 Titanium Alloys 0.0016 0.0024 0.0031 0.0031 0.0039 0.0047 130 200 260 100 160 230 X Bold numbers in the graph indicate the most recommended value of feed (fz) Adjust cutting speed and feed rate according to the actual machining conditions :1st Recommendation Machining with coolant is recommended for Ni-base heat resistant alloy and titanium alloys 2nd Recommendation Ramping / Helical Milling Ramping / Helical Milling Ramping angle should be under a0. For plunge depth per revolution when helical milling, see the cutting performance data of each tool. Use compressed air during machining. Cutting Dia. Applicable Inserts Max. Ramping Angle (a°) 00.375", 08mm Not Recommended 010mm 1.5° 00.500" 012mm, 014mm 2° 00.625", 016mm 3° 017mm, 018mm BDMT 0703 1.5° 00.750", 020mm 2° 021mm 1.8° 01.000", 025mm 1.3° 026mm 1.2° 01.250", 032mm o 033mm 0.5° Minimum Cutting Dia. for Helical Milling MECX Cutting Dia. 00.375" 00.500" 00.625" 00.750" 08mm 010mm 012mm 014mm 016mm 017mm 018mm 020mm BDMT0703 Type Min. Cutting Dia. 00.512" 00.748" 00.984" 01.260" Not recommended for helical milling. 014mm 018mm 022mm 026mm 028mm 030mm 034mm Min. Cutting Dia. for Flat Bottom 00.630" 00.866" 01.142" 01.378" 017mm 021mm 025mm 029mm 031mm 033mm 037mm MECX Cutting Dia. 01.000" 01.250" 021mm 025mm 026mm 032mm 033mm BDMT0703 Type Min. Cutting Dia. 01.732" 02.244" 036mm 044mm 046mm 058mm 060mm Min. Cutting Dia. for Flat Bottom 01.890" 02.362" 039mm 047mm 049mm 061mm 063mm E26