830 Каталог ISCAR 2017 Вращающийся режущий инструмент и инструментальная оснастка Стр.826

Каталог ISCAR 2017 Ротационный инструмент Стр. 826 0830 ENG Lab2u

ITS BORE USER GUIDE ITSSGnE BHR Rough Boring Cutting Data ISO Workpiece Material Hardness HB Overhang L/D Глубина резания в мм ap (mm) R (Radius) Boring Range D18-28 Boring Range D28-50 Boring Range D50-68 0.5-1.0 0.2-0.4 1.0-1.8 0.4 0.5-1.0 0.2-0.4 1.0-1.8 0.4 0.5-1.2 0.2-0.4 1.2-2.0 0.4-0.8 K Grey Cast Iron GG 10-25 HB<200 2.5 Vc (m/min) f (mm/rev) 120-160 0.06-0.15 100-140 0.06-0.18 120-180 0.06-0.15 110-150 0.06-0.12 120-180 0.08-0.2 110-150 0.08-0.12 4 Vc (m/min) f (mm/rev) 100-140 0.06-0.12 80-120 0.06-0.1 100-150 0.06-0.12 80-120 0.06-0.1 100-150 0.08-0.12 80-120 0.08-0.1 6.3 Vc (m/min) f (mm/rev) 70-100 0.06-0.1 60-90 0.06-0.1 70-100 0.06-0.1 60-90 0.06-0.1 70-100 0.08-0.1 60-90 0.08-0.1 Grey Cast Iron GG 25-40 2.5 Vc (m/min) f (mm/rev) 140-200 0.06-0.15 140-200 0.06-0.18 140-220 0.06-0.15 160-250 0.06-0.18 180-220 0.08-0.2 200-280 0.1-0.25 4 Vc (m/min) f (mm/rev) 120-160 0.06-0.12 120-160 0.06-0.14 120-180 0.06-0.12 140-200 0.06-0.14 140-180 0.08-0.12 180-220 0.08-0.2 6.3 Vc (m/min) f (mm/rev) 70-100 0.06-0.1 60-90 0.06-0.1 70-100 0.06-0.1 60-90 0.06-0.1 60-100 0.08-0.1 60-120 0.08-0.1 Cast Iron GGG Spheroidal & Graphite 2.5 Vc (m/min) f (mm/rev) 120-180 0.06-0.15 120-180 0.06-0.18 120-200 0.06-0.15 140-220 0.06-0.18 180-220 0.08-0.18 180-240 0.1-0.2 4 Vc (m/min) f (mm/rev) 120-160 0.06-0.12 120-160 0.06-0.14 120-180 0.06-0.12 140-200 0.06-0.14 140-200 0.08-0.12 160-220 0.08-0.18 6.3 Vc (m/min) f (mm/rev) 60-100 0.06-0.1 60-90 0.06-0.1 60-100 0.06-0.1 60-90 0.06-0.1 60-90 0.08-0.1 60-100 0.08-0.1 ISO Workpiece Material Hardness HB Overhang L/D Глубина резания в мм ap (mm) R (Radius) Boring Range D68-120 Boring Range D120-200 Boring Range D50-68 0.8-1.8 0.2-0.4 1.8-2.5 0.4-0.8 0.8-2.0 0.2-0.4 2.0-3.0 0.4-0.8 0.8-2.0 0.2-0.4 2.0-3.5 0.4-0.8 K Grey Cast Iron GG 10-25 HB<200 2.5 Vc (m/min) f (mm/rev) 120-200 0.08-0.25 110-150 0.08-0.3 150-250 0.08-0.25 180-280 0.08-0.35 150-250 0.08-0.25 180-280 0.08-0.35 4 Vc (m/min) f (mm/rev) 100-150 0.08-0.18 80-120 0.08-0.2 120-170 0.08-0.18 120-170 0.08-0.25 N.R N.R 6.3 Vc (m/min) f (mm/rev) 70-100 0.08-0.15 60-90 0.08-0.12 N.R N.R N.R N.R Grey Cast Iron GG 25-40 4 2.5 Vc (m/min) f (mm/rev) 250-300 0.12-0.35 250-350 0.12-0.35 250-350 0.15-0.3 250-350 0.15-0.4 250-350 0.15-0.3 250-350 0.15-0.4 4 Vc (m/min) f (mm/rev) 200-270 0.1-0.25 230-300 0.12-0.3 200-300 0.15-0.3 200-270 0.15-0.35 N.R N.R 6.3 Vc (m/min) f (mm/rev) 70-150 0.1-0.15 60-120 0.12-0.25 N.R N.R N.R N.R Cast Iron GGG Spheroidal & Graphite 2.5 Vc (m/min) f (mm/rev) 200-240 0.12-0.3 200-280 0.12-0.3 200-280 0.15-0.3 220-300 0.15-0.35 220-300 0.15-0.3 220-300 0.15-0.35 4 Vc (m/min) f (mm/rev) 160-220 0.1-0.2 180-240 0.12-0.25 180-250 0.12-0.2 200-270 0.15-0.35 N.R N.R 6.3 Vc (m/min) f (mm/rev) 60-100 0.1-0.15 60-100 0.12-0.2 N.R N.R N.R N.R N.R. = Not Recommended Stability - Good - Normal - Poor L- 1 1 m In case of a single or a stepped boring cutter configuration, only half the feed should be applied. 826 ISCAR