436 Каталог ISCAR 2017 Токарный металлорежущий инструмент и инструментальная оснастка Стр.432

Каталог ISCAR 2017 Токарный инструмент и оснастка Стр. 432 0436 ENG Lab2u

FACE GROOVING PICCOCUT PICCO-620 (groove along shaft) Inserts for Grooving Along a Shaft Dmin 6 mm Dimensions IC1008 Recommended Machining Data f face-groove (mm/rev) Designation Di min W T max-a d a l2 ll PICCO R 620.1006-20 6.0 1.00 2.00 6.00 5.20 20.0 35.00 0.01-0.04 PICCO R 620.1506-20 6.0 1.50 3.00 6.00 5.20 20.0 35.00 0.01-0.05 6.0 2.00 4.00 6.00 5.20 20.0 35.00 0.02-0.06 PICCO R 620.2506-20 6.0 2.50 5.00 6.00 5.20 20.0 35.00 0.02-0.06 PICCO R 620.3006-20 6.0 3.00 6.00 6.00 5.20 20.0 35.00 0.02-0.06 Only right-hand inserts are available as standard, left-hand inserts on request. All carbide inserts are with sharp corners For detailed cutting data, see pages 466-467 PICCOCUT PICCO-016/020 (face grooving) Inserts with Coolant Holes for Deep Face Grooving Dimensions IC1008 Recommended Machining Data f face-groove (mm/rev) Designation D1 min W Tmax-a d a l1 PICCO R 016.0300-10 16.0 3.00 10.00 8.00 5.50 30.00 0.01-0.05 PICCO R 016.0300-20 16.0 3.00 20.00 8.00 5.50 40.00 0.01-0.05 PICCO R 016.0400-10 16.0 4.00 10.00 8.00 6.00 30.00 0.01-0.05 PICCO R 016.0400-20 16.0 4.00 20.00 8.00 6.00 40.00 0.01-0.05 PICCO R 020.0300-25 20.0 3.00 25.00 8.00 5.50 45.00 0.01-0.05 PICCO R 020.0300-30 20.0 3.00 30.00 8.00 5.50 50.00 0.01-0.04 PICCO R 020.0300-35 20.0 3.00 35.00 8.00 5.50 55.00 0.01-0.04 PICCO R 020.0300-40 20.0 3.00 40.00 8.00 5.50 60.00 0.01-0.04 PICCO R 020.0400-25 20.0 4.00 25.00 8.00 6.00 45.00 0.01-0.06 PICCO R 020.0400-30 20.0 4.00 30.00 8.00 6.00 50.00 0.01-0.06 PICCO R 020.0400-35 20.0 4.00 35.00 8.00 6.00 55.00 0.01-0.05 PICCO R 020.0400-40 20.0 4.00 40.00 8.00 6.00 60.00 0.01-0.05 PICCO R 020.0500-20 20.0 5.00 20.00 8.00 6.50 40.00 0.02-0.06 PICCO R 020.0500-25 20.0 5.00 25.00 8.00 6.50 45.00 0.02-0.06 PICCO R 020.0500-30 20.0 5.00 30.00 8.00 6.50 50.00 0.02-0.06 PICCO R 020.0500-35 20.0 5.00 35.00 8.00 6.50 55.00 0.02-0.05 PICCO R 020.0500-40 20.0 5.00 40.00 8.00 6.50 60.00 0.02-0.05 All inserts have two coolant holes which may be used with coolant pressure up to 100 bars. For detailed cutting data, see pages 466-467 PICCOCUT PICC0-015 (face grooving) Inserts for Deep Face Grooving Dimensions IC228 Recommended Machining Data f face-groove (mm/rev) Designation D1 min W Tmax-a d a l2 l1 PICCO R 015.2515-20 15.0 2.50 20.00 7.00 5.90 20.0 35.00 0.01-0.04 PICCO R/L 015.3015-20 15.0 3.00 20.00 7.00 5.90 20.0 35.00 0.02-0.05 PICCO R 015.3015-30 15.0 3.00 30.00 7.00 5.90 30.0 45.00 0.01-0.04 Only right-hand inserts are available as standard, left-hand inserts on request. All inserts are with sharp corners For detailed cutting data, see pages 466-467 432 ISCAR