176 Каталог ISCAR 2017 Токарный металлорежущий инструмент и инструментальная оснастка Стр.172

Каталог ISCAR 2017 Токарный инструмент и оснастка Стр. 172 0176 ENG Lab2u

ISOTURN INSERTS WCGT Trigon Inserts with a 7° Positive Flank and Chipformer for Finish Turning Dimensions Tough Hard Recommended Machining Data Designation l di S r IC908 IC30N ap (mm) f (mm/rev) WCGT 020102L 2.18 3.97 1.59 0.20 0.40-2.00 0.05-0.10 WCGT 020104L 2.18 3.97 1.59 0.40 0.40-2.00 0.10-0.15 For user guide and cutting speed recommendations, see pages 197-212 For tools, see pages: A/E-SWUCR (99) MG-SWUCR (99) WPEX 80° and 84° Precision Trigon Inserts with Positive 8° and 12° Clearance for Finishing Applications alpha di di J 90°p 60° a Dimensions Tough Hard Recommended Machining Data Designation l S r di d1 alpha a° 8 0 IC IC908 ap (mm) f (mm/rev) WPEX 040200R/L08 4.00 2.50 0.00 6.60 3.20 84.0 8.00 0.20-2.00 0.05-0.20 WPEX 040200R/L12 4.00 2.50 0.00 6.60 3.20 84.0 12.00 0.20-2.00 0.05-0.20 WPEX 040202R/L08 4.00 2.50 0.20 6.60 3.20 84.0 8.00 0.20-2.00 0.05-0.20 WPEX 050300R/L08 5.00 3.18 0.00 7.94 3.70 80.0 8.00 0.20-2.50 0.05-0.20 WPEX 050300R12 5.00 3.18 0.00 7.94 3.70 80.0 12.00 0.20-2.50 0.05-0.20 WPEX 050302R/L08 5.00 3.18 0.20 7.94 3.70 80.0 8.00 0.20-2.50 0.05-0.20 WPEX 050302R/L12 5.00 3.18 0.20 7.94 3.70 80.0 12.00 0.20-2.50 0.05-0.20 WPEX 050304R/L08 5.00 3.18 0.40 7.94 3.70 80.0 8.00 0.20-2.50 0.05-0.20 WPEX 050304R/L12 5.00 3.18 0.40 7.94 3.70 80.0 12.00 0.20-2.50 0.05-0.20 WPEX 060400R/L08 6.00 4.00 0.00 9.52 3.70 80.0 8.00 0.20-3.00 0.05-0.20 WPEX 060400R/L12 6.00 4.00 0.00 9.52 3.70 80.0 12.00 0.20-3.00 0.05-0.20 WPEX 060402R/L08 6.00 4.00 0.20 9.52 3.70 80.0 8.00 0.20-3.00 0.05-0.20 WPEX 060402R/L12 6.00 4.00 0.20 9.52 3.70 80.0 12.00 0.20-3.00 0.05-0.20 WPEX 060404R/L08 6.00 4.00 0.40 9.52 3.70 80.0 8.00 0.20-3.00 0.05-0.20 WPEX 060404R12 6.00 4.00 0.40 9.52 3.70 80.0 12.00 0.20-3.00 0.05-0.20 For user guide and cutting speed recommendations, see pages 197-212 For tools, see pages: SWAPR-PAD (62) SWAPR/L (62) SWDPR/L (62) S SCGT-AS Square Inserts with a 7° Positive Flank, Very Positive Rake Angle and Sharp Cutting Edge for Machining Aluminum di Dimensions Recommended Machining Data Designation l di S r d1 IC20 ap (mm) f (mm/rev) SCGT 09T308-AS 9.52 9.52 3.97 0.80 4.40 0.50-3.00 0.10-0.30 SCGT 120408-AS 12.70 12.70 4.76 0.80 5.50 1.00-4.00 0.10-0.30 For user guide and cutting speed recommendations, see pages 197-212 For tools, see pages: SSBCR/L (59) SSSCR/L (59) di S 90 172 ISCAR