457 Каталог INGERSOLL 2011 Режущий инструмент и инструментальная оснастка Стр.459

Каталог INGERSOLL 2011 Инструмент и оснастка Стр. 459 0457 Lab2u

GENERAL TECHNICAL INFORMATION DATA FOR REGRINDING SOLID CARBIDE MILLS RA Pra Rra SRa tA aA PA SA W A A1 Lw .300" 30 12 13 2.5 5 10 .300" 30 10 12 2 5 10 .300" 38-45 12 13 .300" 38-45 10 12 .5 6 7 .300" 30-45 11 13.5 1.5 5 .300" 30-45 10 12 1.5 5 7 .300" 45 10 11 1.5 5 .300" 45 10 10 1.5 5 7 .007xd1 11.5 7 .007xd1 11.0 .007xd1 10.5 6 .006xd1 9.5 .0065xd1 10.E 6 .006xd1 9.5 6 .0055xd1 9.0 6 .005xd1 8.5 .004xd1 .004xd1 .004xd1 .004xd1 .004xd1 .004xd1 .003xd1 .003xd1 .300" 30 12 11 22 7 11 22 .007xd1 11.0 22 .0023xd1 .004xd1 .300" 30 22 6 11 22 .0065xd1 11.0 22 .002xd1 .004xd1 .300" 30 12 11 22 7 11 22 .007xd1 11.0 22 .0023xd1 .004xd1 .300" 30 22 6 11 22 .0065xd1 11.0 22 .002xd1 .004xd1 .300" 30 12 11 23 7 11 23 .007xd1 11.0 23 .0023xd1 .004xd1 .300" 30 22 6 11 22 .0065xd1 11.0 22 .002xd1 .004xd1 Parameters Parametres: 017xd1) 2 .0060xd1 017xd1) 2 .0058xd1 017xd1) 2 .0060xd1 017xd1) 2 .0058xd1 017xd1) 2 .0060xd1 017xd1) 2 .0058xd1 .300" 38-45 12 13.5 25 3 8 8 17 .007xd1 10.8 21 .0023xd1 .004xd1 (.017xd1) 2 .0060xd1 .300" 38-45 10 12 25 3 8 8 17 .0065xd1 10.0 21 .002xd1 .004xd1 (.017xd1) 2 .0058xd1 .300" 30-45 11 13.5 25 3 8 8 17 .007xd1 10.8 21 .0023xd1 .004xd1 (.017xd1) 2 .0060xd1 .300" 30-45 10 12 25 3 8 8 17 .0065xd1 10.0 21 .002xd1 .004xd1 (.017xd1) 2 .0058xd1 .300" 45 10 11 16 2 8 7 16 .0055xd1 9.0 16 .0023xd1 .004xd1 (.017xd1) 2 .0050xd1 .300" 45 10 10 18 1.5 7 7 16 .005xd1 8.5 17 .002xd1 .004xd1 (.017xd1) 2 .0046xd1 .300" 45 12 10 2.5 7 7 17 .008xd1 9.0 .008xd1 .300" 45 11 9 2.5 5 7 17 .008xd1 8.0 .006xd1 .300" 45-55 18 14 27 4 11 12 25 .0065xd1 13.0 26 .0023xd1 .004xd1 (.017xd1) 2 .0060xd1 .300" 45-55 17 13 26 4 11 11 24 .0075xd1 12.0 25 .002xd1 .004xd1 (.017xd1) 2 .0067xd1 d1 Cutter diameter PA Axial primary relief angle a Helix angle SA Axial secondary clearance angle Ra Radial rake angle aA Axial rake angle PRa Radial primary relief anglel Aw Axial land width SRa Radial secondary clearance angle A Radius chamfer primary relief angle W Radial flute width A1 Radius chamfer 2nd clearance angle Lw Radial land width P Radius Chamfer land tA Dish angle B Radius chamfer flute land Regrinding and surface coating of end mills 1. Regrinding may not influence the original composition of surface substrate. 2. End mills have to be cleansed after regrinding to remove oil or other dirt. Areas that have to be coated should be cleaned once more shortly before. Thickness of coating to be 2 - 4 pm for TiCN- and TiAIN-alloys. 6 2 6 8 6 8 7 7 End mill 2 flutes 3 flutes 4 flutes 6 flutes Ball nose mill 2 flutes 3 flutes 4 flutes End mill with corner radius 3 flutes 4 flutes 6 flutes Rough mill Aluminum mill 2 flutes 459