359 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.359

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 359 0359 ENG Lab2u

Hoffmann Group 47 Solid Type arhi Aa L J M carbide Standard tl9 W 0- 20° 4 V i71 DIN 6535 HA Solid carbide end torus cutter HPC HPC Special centre cutting edge geometry for traverse milling at very high feed rates. Application: For copy and traverse milling over the full range of hard machining under HPC/HSC conditions. Using special milling strategies very high rates of metal removal can be achieved. Note: Comply strictly with ap Recommended application values (v, and fj apply to ap mlx. Use end mills up to the wear limit - special geometry not suitable for regrinding Ground recess 206272 206274 Suitable for/ v( m/min Alu plastics Alu ,< cast <%a >10WSi X < 500 N X < 750 N X < 900 N X < 1100 N X < 1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900N INOX > 900 N Ti > B50N Graphite GRP CRP Uni 6 i ISO code N N P H N 206272 155 145 140 130 O o 206274 150 140 135 125 O o 0h9 Dr 206272 20 6274 Solid carbide end torus cutter No. of teeth Z Programming radius „trans- -15 i HPC verse k L 206272 4 20 6274 0D4 I, 206272 “"20 6274 1 206272 I 206274 mm TiAIN mm 2 54.65 63.95 2 0.15 0.3 1.5 10 15 1.7 50 70 6 0.026 0.019 3 54.65 63.95 2 0.2 0.3 1.5 10 15 2.7 50 70 6 0.056 0.044 4 53.86 66.92 2 0.25 0.5 2 12 20 3.6 60 80 6 0.076 0.06 5 53.46 68.71 4 0.35 0.5 3 13 24 4.6 60 100 6 0.099 0.079 6 52.27 65.93 4 0.4 1 3 13 24 5.2 60 100 6 0.106 0.085 8 60.79 84.35 4 0.5 1.5 4 19 38 7 63 100 8 0.158 0.127 10 93.26 115.83 4 0.7 2 5 22 45 9 72 100 10 0.216 0.172 12 124.74 153.95 4 0.8 2 6 26 53 11 83 120 12 0.266 0.213 16 213.84 - 4 1 2.5 8 32 - 14.5 92 - 16 0.344 - Solid Type carbide L - Standard h9 wl DIN 6535 HA HPC JbbwiM Solid carbide end torus cutter HPC Special centre cutting edge geometry for traverse milling at very high feed rates. Application: For copy and traverse milling in hard machining under HPC / HSC con- ditions. Special milling strategies allow very high metal removal rates. Note: Comply strictly with a„ m„ Recommended application values (v, and fj apply to apm „. Use end mills up to the wear limit - special geometry not suitable for regrinding Ground recess 206276 ) Ground recess 206278 Suitable for/ v, m/min Alu Alu plastics ca5t omu 3 > 10% si X < 500 N X X < 750 N < 900 N X < 1100 N X <1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900 N INOX >900 N Ti >850N Graphite GRP CRP Uni 4 i k ISO code NNN P H hri 206276 125 100 90 50 O O 206278 120 5 85 45 O O 0h9 Dr 206276 - 20 6278 Solid carbide end torus cutter No. of teeth Z Programming radius „trans- ffl ii 1 HPC verse k L 206276 4 20 6278 0D4 I, 206276 ‘ 206278 1 206276 I 206278 mm TiAIN mm 2 55.24 64.15 2 0.06 0.3 1.5 10 15 1.7 50 70 6 0.024 0.018 3 55.24 64.15 2 0.1 0.3 1.5 10 15 2.7 50 70 6 0.05 0.037 4 54.25 66.92 2 0.15 0.5 2 12 20 3.6 60 80 6 0.067 0.049 5 54.25 68.71 4 0.17 0.5 3 13 24 4.6 60 100 6 0.078 0.059 6 52.27 68.31 4 0.2 1 3 13 24 5.2 60 100 6 0.088 0.065 8 60.79 84.35 4 0.25 1.5 4 19 38 7 63 100 8 0.115 0.086 10 94.45 121.28 4 0.3 2 5 22 45 9 72 100 10 0.158 0.116 12 122.27 157.41 4 0.4 2 6 26 53 11 83 120 12 0.178 0.13 16 218.79 - 4 0.5 2.5 8 32 - 14.5 92 - 16 0.229 - 359