Plunge milling cutter Garant 90° and 93° MTC for DGT Greater tool stiffness by elimination of twist between indexable insert and insert seat Plun

Plunge milling cutter Garant 90° and 93° MTC for DGT Greater tool stiffness by elimination of twist between indexable insert and insert seat. Plunge milling cutter 90° for VDGT 11T2 211847 0 D / number of teeth Z mm S 21 1847 1 jfecmnt 1 Plunge milling cutter 90° Weldon shank L, mm Uot mm 0 Ds h6 mm Suitable milling insert Pack of insert screws 11T2 HsSSH MTC Version 16/2 30 80 16 VDGT11T2 219801 (7IP; 0.9 Nm) 20/2 35 85 20 VDGT11T2 21 9801 (7IP; 0.9 Nm) 25/3 35 90 25 VDGT11T2 21 9801 (7IP; 0.9 Nm) Form fit da 0 D / number of teeth Z mm 21 1851 1 ifecmf 1 Plunge milling cutter 90° with threaded shank 0 D, h6 mm Uot mm 0 d2 mm Mounting thread M Suitable milling insert Pack of insert screws 16/2 8.5 35 12.7 M8 VDGT11T2 21 9801 (7IP; 0.9 Nm) 20/2 10.5 35 17.7 M10 VDGT11T2 219801 (7IP; 0.9 Nm) 25/3 12.5 35 20.7 M12 VDGT11T2 21 9801 (7IP; 0.9 Nm) 32/4 17.0 42 28.7 M16 VDGT11T2 21 9801 (7IP; 0.9 Nm) 0D I i 0D, M 0D, I "Min t t I 211851 Plunge milling cutter 93° for VDGT 11T2 Application To prevent chips jamming, especially when milling deep pockets. -fel 93‘ 0 D / number of teeth Z mm 21 1852 1 j&Grat-1 Plunge milling cutter 93° with threaded shank 0D, h6 mm Uot mm 0D2 mm Mounting thread M Suitable milling insert Pack of insert screws 16/2 8.5 35 12.7 M8 VDGT11T2 21 9801 (7IP; 0.9 Nm) 20/2 10.5 35 17.7 M10 VDGT11T2 21 9801 (7IP; 0.9 Nm) 25/3 12.5 35 20.7 M12 VDGT11T2 21 9801 (7IP; 0.9 Nm) 32/4 17.0 42 28.7 M16 VDGT11T2 21 9801 (7IP; 0.9 Nm) 7 0D2 M0D,i 1 211852 Garant Milling inserts for plunge milling cutters No. 211806 - 211852 S'vTjS Version SjiSyTS 21 1853/1856/1857/1859/1858/1867/1868/1862- Fine-grain surface structure, polished chip breaker surface - extreme reduction in the tendency BP t0 ec 9e build-up. 21 1860/1864- Diamond-coated milling insert for higher cutting speeds and longer tool life in materials with silicon content. to Suitable for/ vc m/min Alu plastics osaSL, Alu oija Alu cast >10% Si <500 N <750 N <900 N <1100N <1400 N 900 N Ti >850 N GG(G) CuZn i Uni _5f= max min Air ISO code N P H K N 1 1 HU 7810 1900 1900 500 400 100 O HB 7810 1900 1900 680 o VCG. 2205 FN Note ap max 15 mm for roughing with ae 1 xD. tm Type ALU 1 S21 1853 VCGX 220505 FN HU 7810 10 S21 1856 VCGX 220508 FN HU 7810 10 21 1857 VCGX 220516 FN HU 7810 10 21 1859 VCGX 220520 FN HU 7810 10 21 1858 VCGT 220530 FN HU 7810 10 21 1860 HB 7810 1 fz mm 0.25 211853 211858 211860 VDGT 11T2 FN Note ap max 8 mm for roughing with ae 1 xD, Type ALU 21 1867 VDGT 11T204 FN HU 7810 10 211868 VDGT 11T208 FN HU 7810 10 211862 VDGT 11T210 FN HU 7810 10 21 1864 HB 7810 1 fz mm 0.17 211862 211864 384 Main catalogue Hoffmann Group 46