Garant 45° indexable chamfer mills, positive for SD T 0903 45° 45 Application 2 component edges can be chamfered simultaneously due to two insert

Garant 45° indexable chamfer mills, positive for SD.T 0903 45° 45 Application 2 component edges can be chamfered simultaneously due to two insert edges being exposed; chamfering is possible forwards and reverse. Note 0 Dmin minimum infeed 0 of the workpiece for reverse chamfering. 0 D i 216100 1 i&Gmnt" 45° chamfer mill Number of cutting edges Z 0 Dmin 0Dml L, Uot 0DS h6 Pack of insert screws mm Weldon shank mm 8 1 20.4 20.2 17 80 16 21 9804 (15IP; 3.8 Nm) 16 2 28.5 28.3 20.5 110 16 219805 (15IP; 3.8 Nm) 17,5 3 30.0 29.8 25 110 16 219805 (15IP; 3.8 Nm) 23,5 4 36.0 35.8 30 130 20 219805 (15IP; 3.8 Nm) 25 2 37.5 37.3 27 130 25 219805 (15IP; 3.8 Nm) 33,5 5 46.0 45.8 30 140 25 219805 (15IP; 3.8 Nm) 0D, 0D, 216102 0 D mm i 216102 1 jfecmnt0 45° chamfer mill with threaded shank Number of cutting edges Z 0Dmin mm 0 0 mm 0 D, h6 mm 0 d2 mm L, mm Uot mm Mounting thread M Pack of insert screws 8 1 20.4 20.2 6.5 9.75 14 23 M6 219804 (15IP; 3.8 Nm) 16 2 28.5 28.3 10.5 17.7 18 28 M10 219805 (15IP; 3.8 Nm) 17,5 3 30.0 29.8 10.5 17.7 18 30 M10 219805 (15IP; 3.8 Nm) 23,5 4 36.0 35.8 12.5 20.7 23 35 M12 219805 (15IP; 3.8 Nm) 25 2 37.5 37.3 12.5 20.7 23 35 M12 219805 (15IP; 3.8 Nm) 33,5 5 46.0 45.8 17.0 28.7 24 40 M16 219805 (15IP; 3.8 Nm) ifcGarant" Milling inserts SD.T 0903 for 45° chamfer mills No. 216100 / 6102 Version Strong milling inserts, precision sintered with positive chip breakers. Face and seating surfaces precision ground. Suitable for/ Alu plastics Alu cast >10% Si 2 25 s y -y "- ’ -y" INOX Ti GG(G) CuZn B Uni i a Air vc m/min <500 N <750 N <900 N <67HRC <900 N >900 N >850 N max min ISO code N P p P H K N 1 1 HU 7815- 250 250 120 250 O HB 7535 - 250 250 120 260 220 170 100 80 120 90 100 150 O Type ALU UNI 21 6408 SDGT 090308 FN HU 7815 10 S21 6410 SDLT 090308 EN HB 7535 10 fz mm/rev 0.15 j&Gajariiri High-performance 45° chamfer mill for SCLT 05T1 0 0 Application For effective machining especially for small chamfering operations. For forwards and reverse chamfering at high speeds. 0D I Note 0 Dmln Minimum infeed 0 of the workpiece for reverse chamfering. 0L min I 1 X \ L' 0 D mm 21 6460 1 XbGmit’ High-performance 45° chamfer mill plain shank Number of cutting edges Z 0 Dmin mm 0 Dmax mm L, mm Uot mm 0Dsh6 mm Pack of insert screws jiJTT 2 1 - 8.5 20 80 10 21 9828 (6IP; 0.65 Nm) 6 1 12.7 12.5 20 80 10 21 9828 (6IP; 0.65 Nm) 9 2 15.9 15.7 24 90 10 21 9828 (6IP; 0.65 Nm) 12 4 18.7 18.5 24 100 12 21 9828 (6IP; 0.65 Nm) 16 5 22.9 22.7 20 110 12 21 9828 (61P; 0.65 Nm) 20 6 26.9 26.7 20 120 16 21 9828 (61P; 0.65 Nm) 414 Main catalogue Hoffmann Group 46