1082 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.K050

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. K050 1082 Lab2u

EXCHANGEABLE HEAD END MILLS iMX-CH3L Chamfer head, 3 flute Carbon Steel, Alloy Steel, Cast Iron (<30HRC) Tod Steel, fte-Hardened SW.Hardened Steel (545HRC) Hardened Steel ( 55HRC) Hardened Steel (>55HRC) Austenitic Stainless Steel Titanium Alloy, Heat Resistant Alloy Copper Alloy Aluminium Alloy LU D o /> m /> D Q O' a LU o. DCN=1.5 ±0.020 I Chamfered cutting head suitable for inner and outer circumference. \Anti-vibration priority design. (mm) Order Number DC APMX KAPR DCN LH DCON No. of 1 Flutes Grade o CN o 1 a. LU Type IMX10CH3L100A45 10 4.2 45° 1.5 16 9.7 3 1 IMX12CH3L120A45 12 5.2 45° 1.5 19 11.7 3 1 IMX16CH3L160A45 16 7.2 45° 1.5 24 15.5 3 1 IMX20CH3L200A45 20 9.2 45° 1.5 30 19.5 3 1 Note 1) The fastening size of the holder and head should be the same. (Refer to K002) RECOMMENDED CUTTING CONDITIONS Chamfer milling (Hole circumference) (mm) 5 Q Z LU LlI X LU l CQ LLI o z z o X LLI Work Material Carbon steels, Alloy steels, Gray cast irons AISI 1045, AISI 4140, AISI No 45 B Alloy tool steels, Carbon steels, Alloy steels, Pre-hardened steels SKD, SKT, AISI 4340, AISI P21, AISI P20 Austenitic stainless steels, Titanium alloys AISI 304, AISI 316, Ti-6AI-4V Dia. DC No. of Flutes Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth ofcut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae 10 12 16 20 40 40 40 40 1300 1100 800 640 0.04 0.04 0.04 0.04 160 130 96 77 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 40 40 40 40 1300 1100 800 640 0.03 0.03 0.03 0.03 120 99 72 58 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 30 30 30 30 950 800 600 480 0.03 0.03 0.03 0.03 86 72 54 43 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 Depth of Cut Note 1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 2) Vibration may occur if the rigidity of machine or work material is low. In this case, please reduce the revolution and the feed rate proportionately. : Inventory maintained in Japan. K050