993 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J371

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J371 0993 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Side milling HSIotting Work Material Aluminium alloy Aluminium alloy casting Dia. Revolution Feed rate Revolution Feed rate DC (mm) (min'1) (mm/min) (min'1) (mm/min) 10 19000 8600 9500 3400 12 16000 8200 8000 3200 16 12000 7600 6000 3100 18 10500 7200 5300 2900 20 9500 7100 4800 2900 22 8500 6900 4300 2800 25 7500 6800 3800 2700 Depth of cut 0.5DC 1DC DC:Dla. Work Material Aluminium alloy Aluminium alloy casting Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 10 19000 6800 9500 2700 12 16000 6500 8000 2600 16 12000 6100 6000 2400 18 10500 5800 5300 2400 20 9500 5700 4800 2300 22 8500 5500 4300 2200 25 7500 5400 3800 2200 Depth of cut DC DC:Dia. I 1DC LU CC. D o 10 m cc l±j a. Note 1) Water-soluble cutting fluid is recommended. Note 2) If the depth ofcut is shallow, the revolution and feed rate can be increased. Note 3) Climb cutting is recommended for side milling. Note 4) These end mills do not have a centre cutting edge, therefore when entering a workpiece use a ramping process rather than vertical feed. Note 5) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately, or set the depth of cut smaller. Using a high-speed and high-rigidity machining center Side i milling Work Material Aluminium alloy Aluminium alloy casting Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 10 30000 11000 19000 5400 12 30000 12000 16000 5300 16 24000 12000 12000 4900 18 21000 12000 10500 4700 20 19000 11000 9500 4600 22 17000 11000 8500 4300 25 15000 11000 7500 4300 Depth of cut SO 5 DC i DC: Dia. 1 l/i S1DC Slotl ting Work Material Aluminium alloy Aluminium alloy casting Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 10 30000 8600 19000 4300 12 30000 9900 16000 4300 16 24000 9700 12000 4000 18 21000 9500 10500 3800 20 19000 9100 9500 3700 22 17000 8700 8500 3400 25 15000 8600 7500 3400 Depth of cut DC DC: Dia. I L 0.75DC o in Note 1) Water-soluble cutting fluid is recommended. Note 2) If the depth ofcut is shallow, the revolution and feed rate can be increased, Note 3) Climb cutting is recommended for side milling. Note 4) These end mills do not have a centre cutting edge, therefore when entering a workpiece use a ramping process rather than vertical feed. Note 5) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately, or set the depth of cut smaller. J371