937 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J315

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J315 0937 Lab2u

CARBIDE Work Material Carbon steel, Cast iron, Alloy steel ( 30HRC) AIS11050, AISI No 35 B, AISI P20 Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Dia. DC (mm) Corner R RE (mm) Taper angle one side BHTA2 Neck length LB2 (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) 4 1 0.4" 25 10000 9900 0.24 1.5 8300 7000 0.19 1.5 6700 5600 0.14 1.5 5000 2500 0.07 1.5 4 1 0.4° 30 10000 9900 0.24 1.5 8300 7000 0.19 1.5 6700 5600 0.14 1.5 5000 2500 0.07 1.5 4 1 0.4" 35 10000 9900 0.15 1.5 8300 7000 0.12 1.5 6700 5600 0.09 1.5 5000 2500 0.04 1,5 4 1 0.4" 40 10000 9900 0.15 1.5 8300 7000 0.12 1.5 6700 5600 0.09 1.5 5000 2500 0.04 1.5 4 1 0.4° 45 10000 9900 0.15 1.5 8300 7000 0.12 1.5 6700 5600 0.09 1.5 5000 2500 0.04 1,5 4 1 0.4' 50 8100 6300 0.14 1.5 6700 4420 0.11 1.5 5400 3500 0.08 1.5 4000 1600 0.04 1.5 4 1 0.9' 25 10000 9900 0.24 1.5 8300 7000 0.19 1.5 6700 5600 0.14 1.5 5000 2500 0.07 1.5 4 1 0.9' 30 10000 9900 0.15 1.5 8300 7000 0.12 1.5 6700 5600 0.09 1.5 5000 2500 0.04 1.5 4 1 0.9' 40 10000 9900 0.15 1.5 8300 7000 0.12 1.5 6700 5600 0.09 1.5 5000 2500 0.04 1.5 4 1 0.9' 50 8100 6300 0.14 1.5 6700 4420 0.11 1.5 5400 3500 0.08 1.5 4000 1600 0.04 1.5 4 1 0.9' 60 8100 6300 0.11 1.5 6700 4420 0.08 1.5 5400 3500 0.06 1.5 4000 1600 0.03 1.5 6 1.5 0.9' 40 6600 11000 0.4 2 5500 7600 0.32 2 4500 6100 0.24 2 3300 2700 0.12 2 6 1.5 0.9' 50 6600 11000 0.4 2 5500 7600 0.32 2 4500 6100 0.24 2 3300 2700 0.12 2 6 1.5 0.9' 60 6600 11000 0.25 2 5500 7600 0.2 2 4500 6100 0.15 2 3300 2700 0.08 2 6 1.5 0.9' 70 5400 8700 0.23 2 4400 6200 0.18 2 3600 5000 0.14 2 2700 2200 0.07 2 8 2 0.9' 60 5000 11000 0.48 3 4200 7600 0.37 3 3300 6100 0.29 3 2500 2700 0.14 3 8 2 0.9' 80 5000 11000 0.3 3 4200 7600 0.23 3 3300 6100 0.18 3 2500 2700 0.09 3 10 2 0.9' 80 4000 11000 0.48 4.5 3300 7600 0.37 4.5 2700 6100 0.29 4.5 2000 2700 0.14 4.5 10 2 0.9' 120 3200 8700 0.27 4.5 2700 6200 0.21 4.5 2100 5000 0.16 4.5 1600 2200 0.08 4.5 12 2 0.9' 80 3300 10000 0.72 6 2700 7100 0.56 6 2200 5600 0.36 6 1700 2500 0.18 6 12 2 0.9" 120 3300 10000 0.45 6 2700 7100 0.35 6 2200 5600 0.23 6 1700 2500 0.12 6 Hardened steel (45 55HRC) AISI H13 Hardened steel (55 62HRC) AISI D2 LU CC D o CO m cc LU a. LU CC cc m cd CD 3 o DC Depth of cut Note 1) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 2) Air blow or oil mist is recommended for good chip evacuation. Note 3) For profile machining such as moulds, machining conditions may differ considerably depending on the workpiece geometry, machining methods and depth of cut. Reduce the feed rate especially when machining the corner sections of a workpiece. Note 4) The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. o in J315