Cutting data for mills Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cu

Cutting data for mills Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% 0 Cutting speed m/min Feed rate mm tooth JpLfl ap ae ap min max 3 4 5 6 8 10 12 14 16 18 20 25 P0 15xD 05xD 1xD 130 150 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 P1 15xD 05xD 1xD 140 160 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 P2 15xD 05xD 1xD 120 140 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 P3 15xD 05xD 1xD 100 118 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 P4 15xD 05xD 1xD 67 77 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 P5 15xD 05xD 1xD 109 126 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 P6 15xD 05xD 1xD 95 110 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 P7 15xD 05xD 1xD 60 69 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 P8 15xD 05xD 1xD 40 48 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 M1 15xD 05xD 1xD 67 77 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 M2 15xD 05xD 1xD 38 44 0008 0013 0021 0021 0027 0044 0044 0059 0059 0071 0071 0077 K1 15xD 05xD 1xD 130 150 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 K2 15xD 05xD 1xD 95 110 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 K3 15xD 05xD 1xD 95 110 001 0017 0029 0029 0038 0063 0063 0084 0084 0101 0101 0109 S1 15xD 05xD 1xD 27 31 0006 0008 0013 0013 0021 0027 0027 0044 0044 0059 0059 0063 Cutting data for mills 015 633 Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% Cutting speed m/min Feed rate mm tooth ap ap 10 12 16 20 25 N1 1xD 05xD 1xD 221 313 0008 0014 002 0025 0031 0037 0045 0062 0073 N2 1xD 05xD 1xD 205 290 0008 0014 002 0025 0031 0037 0045 0062 0073 N3 1xD 05xD 1xD 172 245 0008 0014 002 0025 0031 0037 0045 0062 0073 N4 1xD 05xD 1xD 110 156 0008 0014 002 0025 0031 0037 0045 0062 0073 01 1xD 05xD 1xD 158 223 0008 0014 002 0025 0031 0037 0045 0062 0073 3 4 6 8 ae Cutting data for mills 015 645 Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% Cutting speed m/min Feed rate mm tooth ap ae ap min max 3 4 6 8 10 12 16 20 25 N1 1xD 05xD 1xD 247 350 0021 0021 0046 0046 0055 0055 0071 0092 0109 N2 1xD 05xD 1xD 212 300 0021 0021 0046 0046 0055 0055 0071 0092 0109 N3 1xD 05xD 1xD 141 200 0021 0021 0046 0046 0055 0055 0071 0092 0109 N4 1xD 05xD 1xD 127 180 0017 0017 0029 0029 0042 0042 0063 0076 0101 O1 1xD 05xD 1xD 282 400 0017 0017 0029 0029 0042 0042 0063 0076 0101 174 NORGAU