TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ iMX-S4HV-5 Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Cartoon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Oil. DCjmm) Cutting speed (minin) Revdutin (niir'l Feed per Toolh (mmitorth) Table Feed (rnn/min) Depth of cut (mm) Dili of cut a)(min Cutting feed (m/min) Revdution (mir') Feed per Tooth timltooth) Table Feed (mm/min) Depth of cut (mm Width if cut ieH Cutting speed minin) Revdution fir1) Feed per Tooth mnM TahleFeed (mmMn) Depth of cut (mm) Mh if cut aeflnm) 10 150 4800 0.09 1700 10 2 120 3800 0.06 910 10 2 100 3200 0.075 960 10 2 12 150 4000 0.09 1400 12 2.4 120 3200 0.065 830 12 2.4 100 2700 0.08 860 12 2.4 16 150 3000 0.1 1200 16 3.2 120 2400 0.075 720 16 3.2 100 2000 0.09 720 16 3.2 20 150 2400 0.1 960 20 4 120 1900 0.075 570 20 4 100 1600 0.09 580 20 4 25 150 1900 0.12 910 25 5 120 1500 0.075 450 25 5 100 1300 0.09 470 25 5 ae Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Heat resistant alloys lnconel718 Dia. Cutfng speed Revolution Feed per Tooth Table Feed Depth of nt Width of cut Cutting speed Revdution Feed per Tooth TahleFeed Depth of cut Width of cut DCJnm) (m/min) (miir1) mnM) mm/min) (mm) ae(mm) (m/min) (miir1) imMi (rnn/min) (mm) ae nri) 10 75 2400 0.06 580 10 2 40 1300 0.04 210 10 1 12 75 2000 0.065 520 12 2.4 40 1100 0.045 200 12 1.2 16 75 1500 0.075 450 16 3.2 40 800 0.05 160 16 1.6 20 75 1200 0.075 360 20 4 40 640 0.05 130 20 2 25 75 950 0.075 290 25 5 40 510 0.05 100 25 2.5 For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Slotting Work material Cartoon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Dia. Cutting speed Revdution Feed per Tooth TahleFeed Depth if cut Cutfng speed Revolution Feed per Tcolli TahleFeed Depth of cut Cutting speed Revdution Feed per Tooth TahleFeed Depth of cut DC(mm) m(mh (miir1) (mirfath) (mmlmin) M (mtnin) (min1) (mmftooth) (mmlmii) (minin) miir1) mmMi mmMn) (mm 10 100 3200 0.04 510 5 80 2500 0.03 300 5 75 2400 0.03 290 5 12 100 2700 0.05 540 6 80 2100 0.04 340 6 75 2000 0.04 320 6 16 100 2000 0.07 560 8 80 1600 0.05 320 8 75 1500 0.06 360 8 20 100 1600 0.07 450 10 80 1300 0.05 260 10 75 1200 0.06 290 10 25 100 1300 0.08 420 12 80 1000 0.05 200 12 75 950 0.06 230 12 1232 Mitsubishi Materials