Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING

Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING

Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING _ i press Recommended cutting condition Work material Aluminium nitride Alumina Zirconia Dil. Cuttiig Sptsd Million F td rata Sty Cling Spud Ravdution Faad rate Slap Cutting Spaed Ravolutioi Faad rata Sly DC(mm (m/min tyniit (multe ) (mm) (mimh) miir1 im ( I (mlnii (miir1) (mmto) ni) 0.05 3 20,000 0.000015 0.001 3 20,000 0.00001 0.001 3 20,000 0.00001 0.001 0.08 5 20,000 0.00003 0.003 5 20,000 0.00002 0.002 5 20,000 0.00002 0.001 0.1 6 20,000 0.0002 0.01 6 20,000 0.0001 0.005 6 20,000 0.0001 0.003 0.16 g 18,000 0.0002 0.01 g 18,000 0.0001 0.005 g 18,000 0.0001 0.003 0.2 g 15,000 0.0002 0.01 g 15,000 0.0001 0.005 g 15,000 0.0001 0.003 0.32 12 12,000 0.0002 0.01 12 12,000 0.0001 0.005 12 12,000 0.0001 0.003 0.4 15 12,000 0.0002 0.01 15 12,000 0.0001 0.005 15 12,000 0.0001 0.003 0.5 ig 12,000 0.0002 0.01 ig 12,000 0.0001 0.005 ig 12,000 0.0001 0.003 0.6 ig 10,000 0.0002 0.01 ig 10,000 0.0001 0.005 ig 10,000 0.0001 0.003 0.8 25 10,000 0.0002 0.01 25 10,000 0.0001 0.005 25 10,000 0.0001 0.003 1 31 10,000 0.0002 0.01 31 10,000 0.0001 0.005 31 10,000 0.0001 0.003 1.2 30 8,000 0.00025 0.01 30 8,000 0.00015 0.005 30 8,000 0.00015 0.003 1.6 40 8,000 0.0003 0.01 40 8,000 0.0002 0.005 40 8,000 0.0002 0.003 2 38 6,000 0.0003 0.01 38 6,000 0.0002 0.005 38 6,000 0.0002 0.003 3 47 5,000 0.0003 0.01 47 5,000 0.0003 0.005 47 5,000 0.0002 0.003 Work material Silicon carbide Silicon nitride Quartz glass Dil. Cling Spaad RavoMan Faad rata % Cutthg Spaad RavoMm Faad rata Slap DC(mm) (mknin) (mirr1) (mmta (mm) (m/min) miir1) (mm/rev) M 0.05 3 20,000 0.000005 0.0005 3 20,000 0.000015 0.001 0.08 5 20,000 0.00001 0.001 5 20,000 0.00003 0.005 0.1 6 20,000 0.00005 0.002 6 20,000 0.0002 0.05 0.16 g 18,000 0.00005 0.002 g 18,000 0.0002 0.05 0.2 g 15,000 0.00005 0.002 g 15,000 0.0002 0.05 0.32 12 12,000 0.00005 0.002 12 12,000 0.0002 0.05 0.4 15 12,000 0.00005 0.002 15 12,000 0.0003 0.05 0.5 ig 12,000 0.00005 0.002 ig 12,000 0.0003 0.05 0.6 ig 10,000 0.00005 0.002 ig 10,000 0.0003 0.05 0.8 25 10,000 0.00005 0.002 25 10,000 0.0003 0.05 1 31 10,000 0.00005 0.002 31 10,000 0.0003 0.05 1.2 30 8,000 0.00007 0.002 30 8,000 0.0004 0.05 1.6 40 8,000 0.0001 0.002 40 8,000 0.0004 0.05 2 38 6,000 0.0001 0.002 38 6,000 0.0004 0.05 3 47 5,000 0.0001 0.002 47 5,000 0.0005 0.05 Depending on the type of machine, it is possible to apply cutting speeds over 20000min-1. Use water soluble coolant or grinding fluid when working. The intermediate diameter revolution is not tabulated. It is matched to the large diameter side and closest drill diameter conditions or by calculating the cutting speed of the closest drill diameter. Set the feedrate per revolution to a suitable value with the recommended feedrate of the closest drill diameter as the standard. 1788 Mitsubishi Materials