Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ MPMHVRB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Carbon steel, Alloy steel (180 280HB) Ductile Cast Iron AIS11045, AISI 4140, FCD450 Carbon steel, Alloy steel (280 350HB) Pre-hardened steel, Alloy tool steel AISI 4340, AISI P21, AISI P20.SKD, SKT Austenitic stainless steel ( 200HB) Titanium alloy AISI 304, AISI 306,Ti-6AI-4V Hardened steel (45 52HRC) AISI H13, AISI L6 Dia. DCH Revokitkm (mir1) Feed rate (mmknhl Depth of cut ip(im Qefith of cut u(niii Revolution (mir1) Feed nte (mmlmr Depth cf cut ao(mn depth of cut is ur Revdution (mir1) Feed nte (mmlmin) Depth gt cut ip(mm) Deptli of cut ii(mm Revdution (miir1 Feed nte (mmlmin) Depth of cut ipM Depth of cut ao(mm) 1 38000 910 1.7 0.2 31000 500 1.7 0.2 25000 500 1.7 0.2 18000 290 1.7 0.05 2 21000 1500 3.5 0.4 17000 820 3.5 0.4 14000 640 3.5 0.4 10000 320 3.5 0.1 3 16000 1800 5 0.6 13000 940 5 0.6 11000 880 5 0.6 7400 380 5 0.15 4 12000 1700 7 0.8 9500 950 7 0.8 8000 900 7 0.8 5600 400 7 0.2 5 9500 1800 8.5 1 7600 1100 8.5 1 6400 900 8.5 1 4500 430 8.5 0.25 6 8000 2100 10 1.2 6400 1300 10 1.2 5300 1100 10 1.2 3700 440 10 0.3 8 6000 2000 13.5 1.6 4800 1400 13.5 1.6 4000 1200 13.5 1.6 2800 450 13.5 0.4 10 4800 2100 17 2 3800 1500 17 2 3200 1100 17 2 2200 440 17 0.5 12 4000 1900 20.5 2.4 3200 1400 20.5 2.4 2700 1100 20.5 2.4 1900 380 20.5 0.6 16 3000 1400 27.2 3.2 2400 1100 27.2 3.2 2000 840 27.2 3.2 1400 340 27.2 0.8 20 2400 1200 34 4 1900 840 34 4 1600 670 34 4 1100 260 34 1 ae When using a slim shank with DC=10 or 12, reduce the cutting speed by 60%, the feed rate by 80%, and the depth of cutting ae by 50% from the above conditions. Water-soluble cutting fluids are recommended for stainless steel and titanium alloys. Air blowing is recommended for carbon steel. The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Slotting Work material Carbon steel, Alloy steel (180 280HB) Ductile Cast Iron AIS11045, AISI 4140, FCD450 Carbon steel, Alloy steel (280 350HB) Pre-hardened steel, Alloy tool steel AISI 4340, AISI P21, AISI P20.SKD, SKT Austenitic stainless steel ( 200HB) Titanium alloy AISI 304, AISI 306,Ti-6AI-4V Hardened steel (45 52HRC) AISI H13, AISI L6 DU. D(tytl) Revolution (miir1) Feed nte (nlmin Depth of cut ap(mm RevoMn (miir1) Feed nit (nmlmin) Depth of cut ap(mn Reiokition (miir4) Feed nte limtnin) Depth of cut ) Revotutim (miir1) Feed nte (mmMn) Depth of cut ipM 1 31000 620 0.5 24000 380 0.5 20000 320 0.5 9500 110 0.2 2 17000 650 2 14000 450 2 11000 350 2 4800 130 0.4 3 13000 940 3 10000 660 3 8500 510 3 3200 140 0.6 4 9500 820 4 7600 600 4 6400 460 4 2400 150 0.8 5 7600 910 5 6100 670 5 5100 510 5 1900 170 1 6 6400 860 6 5100 630 6 4200 470 6 1600 190 1.2 8 4800 1000 8 3800 750 8 3200 580 8 1200 190 1.6 10 3800 910 10 3100 680 10 2500 500 10 950 150 2 12 3200 920 12 2500 660 12 2100 500 12 800 160 2.4 16 2400 690 16 1900 500 16 1600 380 16 600 120 3.2 20 1900 550 20 1500 400 20 1300 310 20 480 96 4 DC ; IaP I MBS Slotting is not recommended when using a slim shank type. 992 Mitsubishi Materials